M20C-FKS FUEL  FUEL INJECTOR(for Direct Injection)  INSTALLATION  

0.625,0.427 0.938,0.583 0.313,0.156 10 false *a

*a	Area to be Cleaned

Apply engine conditioner to the area shown in the illustration. Using a piece of cloth, clean carbon deposits from the direct fuel injector assembly and its grooves.

NOTICE:

·

Do not clean the tip of the direct fuel injector assembly.

·

Do not use a wire brush to clean the direct fuel injector assembly.

·

If a direct fuel injector assembly is dropped or the tip of the direct fuel injector assembly is struck, replace it with a new one.

0.219,0.979 0.344,0.979 0.344,0.979 0.458,1.125 false 2.104,0.813 2.563,0.813 2.563,0.813 2.563,1.677 false 2.24,0.813 2.24,1.688 false 0.073,0.885 0.385,1.042 0.313,0.156 10 false *a 1.948,0.729 2.26,0.885 0.313,0.156 10 false *b

*a	SST (Guide)
*b	Chamfer

Apply engine oil to the direct fuel injector assembly contact surface of SST (guide), and then attach SST (guide) to the direct fuel injector assembly with the chamfer facing the tip of the direct fuel injector assembly as shown in the illustration.

SST

09260-39030  (09261-03030)

0.99,2.635 1.49,2.635 false 1.01,2.802 1.396,3.042 1.396,3.042 1.49,3.042 false 1.531,2.563 1.729,2.76 0.198,0.198 10 false *a 2.771,0.563 2.969,0.76 0.198,0.198 10 false *c 1.979,0.552 2.177,0.75 0.198,0.198 10 false *b 1.542,2.969 1.74,3.167 0.198,0.198 10 false *1

*1	Fuel Injector Seal
*a	SST (Holder)
*b	Correct
*c	Incorrect

Install a new fuel injector seal to SST (holder).

SST

09260-39030  (09261-03011)

NOTICE:

Be careful not to install the fuel injector seal to SST (holder) at an angle. Doing so will stretch the fuel injector seal.

0.802,1.083 0.917,0.406 0.917,0.406 1.063,0.406 true 1.01,1.719 1.125,1.948 1.125,1.948 1.281,1.948 true 1.104,0.323 1.417,0.479 0.313,0.156 10 false *a 1.333,1.885 1.646,2.042 0.313,0.156 10 false *b

*a	SST (Holder)
*b	SST (Guide)

Install SST (holder) with the fuel injector seal to the tip of the direct fuel injector assembly. Slide the fuel injector seal downward into the direct fuel injector assembly groove with your fingers as shown in the illustration.

SST

09260-39030  (09261-03011, 09261-03030)

HINT:

Check that the fuel injector seal is seated in the direct fuel injector assembly groove as shown in the illustration.

0.667,1.333 0.917,0.417 0.917,0.417 1.104,0.417 true 1.146,0.344 1.458,0.5 0.313,0.156 10 false *a

*a	SST (Guide)

Slowly slide SST (guide) toward the tip of the direct fuel injector assembly. When the direct fuel injector assembly contact surface of SST (guide) aligns with the fuel injector seal as shown in the illustration, hold the position for 5 seconds or more to fully seat the fuel injector seal into the direct fuel injector assembly groove.

SST

09260-39030  (09261-03030)

NOTICE:

Make sure the fuel injector seal is not pinched between SST (guide) and the edge of the direct fuel injector assembly groove. Replace the fuel injector seal if it becomes damaged.

HINT:

·

Set SST (guide) so that its bottom surface is flush with the fuel injector seal.

·

If it is difficult to slide SST (guide) upward, slowly wiggle it from side to side while sliding it up the direct fuel injector assembly little by little.

0.625,2.771 0.938,2.927 0.313,0.156 10 false *a 1.844,2.75 2.156,2.906 0.313,0.156 10 false *b 2.75,2.729 3.063,2.885 0.313,0.156 10 false *c 0.583,0.667 0.896,0.823 0.313,0.156 10 false *d 1.792,0.656 2.104,0.813 0.313,0.156 10 false *e 2.708,0.656 3.021,0.813 0.313,0.156 10 false *e

*a	Normal
*b	Protruding
*c	Deformed
*d	Correct
*e	Incorrect

After installing the fuel injector seals, check that they are not scratched, deformed or protruding from the direct fuel injector assembly groove.

NOTICE:

If a fuel injector seal is scratched, deformed or protruding from the groove, replace it with a new one.

HINT:

Use the same procedure to install the other fuel injector seals.

0.979,0.583 1.094,0.583 1.094,0.583 1.25,0.948 false 2.292,0.375 2.417,0.375 2.417,0.375 2.604,0.656 false 2.438,0.167 2.542,0.167 2.542,0.167 2.771,0.448 false 2.917,0.115 3.031,0.115 3.031,0.115 3.031,0.51 true 0.813,0.51 1.125,0.667 0.313,0.156 10 false *1 2.115,0.302 2.427,0.458 0.313,0.156 10 false *2 2.26,0.094 2.573,0.25 0.313,0.156 10 false *3 2.75,0.021 3.063,0.177 0.313,0.156 10 false *a

*1	Direct Fuel Injector Assembly
*2	C-ring
*3	Injector Vibration Insulator
*a	Taper

Install a new injector vibration insulator and a new C-ring to each direct fuel injector assembly.

NOTICE:

·

Install the taper of the injector vibration insulator by aligning it with the taper of the direct fuel injector assembly.

·

Check that the C-ring is securely seated in the groove of the direct fuel injector assembly.

Install a new O-ring and No. 1 fuel injector back-up ring to each direct fuel injector assembly as shown in the illustration.

5.198,1.313 5.333,1.313 5.333,1.313 5.625,1.792 true 5.917,1.719 6.115,1.281 6.115,1.281 6.219,1.281 true 5.031,1.229 5.344,1.385 0.313,0.156 10 false *1 6.271,1.198 6.583,1.354 0.313,0.156 10 false *2 1.573,0.656 1.885,0.813 0.313,0.156 10 false *a 0.771,1.792 1.083,1.948 0.313,0.156 10 false *b 2.542,1.813 2.854,1.969 0.313,0.156 10 false *c 1.625,1.125 1.938,1.281 0.313,0.156 10 false *d 0.76,1.125 1.073,1.281 0.313,0.156 10 false *e 2.531,1.135 2.844,1.292 0.313,0.156 10 false *e

*1	No. 1 Fuel Injector Back-up Ring	*2	O-ring
*a	No. 1 Fuel Injector Back-up Ring Opening	*b	Overlapped
*c	Stretched	*d	Correct
*e	Incorrect	-	-

NOTICE:

·

Check that there is no foreign matter or damage on the O-ring groove of the direct fuel injector assembly.

·

Make sure that the No. 1 fuel injector back-up ring is installed in the correct orientation.

·

Make sure that the No. 1 fuel injector back-up ring and O-ring are installed in the correct order.

·

Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.

·

After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.

2.833,1.5 3.031,1.5 false 2.76,2.375 2.896,2.281 2.896,2.281 3,2.281 false 2.448,2.448 2.656,2.833 2.656,2.833 2.792,2.833 true 3.073,1.417 3.385,1.573 0.313,0.156 10 false *1 3.042,2.198 3.354,2.354 0.313,0.156 10 false *2 2.833,2.75 3.146,2.906 0.313,0.156 10 false *a

*1	Direct Fuel Injector Assembly
*2	No. 3 Fuel Injector Back-up Ring
*a	Notch

With the notch of a new No. 3 fuel injector back-up ring facing downward, install the No. 3 fuel injector back-up ring to each direct fuel injector assembly as shown in the illustration.

NOTICE:

·

Make sure that the No. 3 fuel injector back-up ring is installed in the correct orientation.

·

After installing the No. 3 fuel injector back-up ring, make sure there is no damage or foreign matter.

0.469,0.292 0.646,0.292 0.646,0.292 1.167,0.458 true 0.479,0.781 0.656,0.781 0.656,0.781 1.146,0.552 true 0.302,0.198 0.615,0.354 0.313,0.156 10 false *a 0.313,0.698 0.625,0.854 0.313,0.156 10 false *b

*a	Protrusion
*b	Positioning Hole
	No Gap

Align the protrusion of the nozzle holder clamp with the positioning hole of the fuel delivery pipe and insert the direct fuel injector assembly.

NOTICE:

·

Make sure that there is no foreign matter or damage inside the direct fuel injector assembly installation holes (fuel delivery pipe).

·

Do not allow gasoline to get on the O-rings or inside the installation holes.

·

If it is difficult to insert the direct fuel injector assembly, apply new engine oil to the chamfer of the direct fuel injector assembly installation hole of the fuel delivery pipe. Be careful not to allow the direct fuel injector assembly to fall out of the fuel delivery pipe.

·

Do not tilt the direct fuel injector assembly when inserting it into the fuel delivery pipe.

·

Check that there is no gap between the fuel delivery pipe and the nozzle holder clamp.

·

1.073,1.656 1.51,1.656 true 1.74,1.646 2.271,1.24 2.271,1.24 2.469,1.24 true 2.521,1.167 2.833,1.323 0.313,0.156 10 false *a 0.906,1.583 1.219,1.74 0.313,0.156 10 false *b

*a	QR Code
*b	Flow Classification Number

As direct fuel injector assemblies with different flow classification numbers are incompatible, make sure the 4 direct fuel injector assemblies have the same flow classification number (the number to the left of the QR code (1, 2, 3, 4, 5, 6, 7, 8 or 9)).

HINT:

When replacing the direct fuel injector assemblies for all cylinders, it is not necessary to use the same flow classification number as those currently installed to the vehicle. However, make sure to replace the direct fuel injector assemblies with new ones that all have the same flow classification number (1, 2, 3, 4, 5, 6, 7, 8 or 9).

0.979,0.083 1.125,0.271 0.146,0.188 10 true 1 2.219,0.615 2.365,0.802 0.146,0.188 10 true 2

Temporarily install the fuel delivery pipe to the cylinder head sub-assembly with the 2 bolt in the order shown in the illustration.

Torque:

10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

·

If a direct fuel injector assembly is dropped or the tip of a direct fuel injector assembly is struck, replace it with a new one.

·

Check that there is no foreign matter or damage on the direct fuel injector assembly installation holes of the cylinder head sub-assembly.

·

When installing the fuel delivery pipe, push it in evenly without tilting it.

1.177,0.25 1.333,0.417 0.156,0.167 10 true 1 2.24,0.698 2.396,0.865 0.156,0.167 10 true 2 0.323,0.115 0.479,0.281 0.156,0.167 10 true 3 3.073,1.135 3.229,1.302 0.156,0.167 10 true 4

Install the fuel delivery pipe by uniformly tightening the 4 bolts in the order shown in the illustration.

Torque:

28.5 N*m (291 kgf*cm, 21 ft.*lbf)