DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Lane Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | 0 to 16777215 | - | Cannot be used |
| Total Distance Traveled - Unit | Unit used for total distance traveled | km or mile | - | Cannot be used |
| LDA Control | Whether lane tracing assist system is permitted or not | Prohibit or Permit | Prohibited: Lane tracing assist system control not possible
Permitted: Lane tracing assist system control possible |
- |
| Turn Switch (Right) | Turn signal switch (right) status | OFF or ON | ON: Turn signal light switch on (right)
OFF: Turn signal light switch off |
- |
| Turn Switch (Left) | Turn signal switch (left) status | OFF or ON | ON: Turn signal light switch on (left)
OFF: Turn signal light switch off |
- |
| Vehicle Information (2WD/4WD) | - | - | - | Cannot be used |
| Vehicle Information (Powertrain Type) | - | - | - | Cannot be used |
| Not Holding Steering Wheel Judgment Status (Torque Sensor) | Judgement status by torque sensor of whether hands are not on steering wheel | Detected or Not Detected | Detected: Judgment of hands not on steering wheel detected
Not Detected: Judgment of hands not on steering wheel not detected |
- |
| Not Holding Steering Wheel Judgment Status (Touch Sensor) | - | - | - | Cannot be used |
| Selected Lane Center Distance | Distance to lane center | -2147483648 to 2147483520 m | Actual distance from vehicle to lane center | When lane center is on right side from vehicle: Displayed by a positive value
When lane center is on left side from vehicle: Displayed by a negative value |
| Driver Torque Input Steering Status | Status of steering torque input by driver | Detected or Not Detected | Detected: Steering input detected
Not Detected: Steering input not detected |
- |
| Driver Torque Cancel Steering Status | Driver cancel steering input status | Detected or Not Detected | Detected: Cancel steering input detected
Not Detected: Cancel steering input not detected |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Lane Control / Active Test.
Perform Active Test according to the display on the GTS.
The ignition switch must be turned to ON to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Buzzer | Sounds the LTA buzzer (meter buzzer) | Start/Stop | Confirm that the vehicle is stopped with the ignition switch ON. |
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform Active Test according to the display on the GTS.
The ignition switch must be turned to ON to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display (All) | Completely illuminates the multi-information display | ON | Confirm that the vehicle is stopped with the ignition switch ON. |