RM36D0EC _59 Vehicle Exterior _083099 MIRROR (EXT) _0400992 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for SFTM Made, w/o Auto Power Retract Mirror)

a.
B525841C02
1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.833,3 1.25,2.667 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 1.938,3.052 1.938,2.719 true 2.688,1.094 3,1.25 0.313,0.156 10 false *1 2.615,1.469 2.927,1.625 0.313,0.156 10 false *2 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR
*1 Mirror Adjust Switch
*2 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for SFTM Made, w/ Auto Power Retract Mirror)

a.
B525839C03
2.125,0.75 2.625,0.75 true 1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.865,3.042 1.281,2.708 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 2.458,3.031 2.292,2.698 true 2.708,3.052 2.417,2.667 true 0.583,2.521 0.917,2.521 true 1.938,3.052 1.938,2.719 true 1.177,2.646 1.177,2.135 1.177,2.135 1.01,2.135 true 2.531,2.677 2.865,2.677 true 2.667,0.677 2.979,0.833 0.313,0.156 10 false *1 2.688,1.094 3,1.25 0.313,0.156 10 false *2 2.615,1.469 2.927,1.625 0.313,0.156 10 false *3 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.385,3.063 2.844,3.26 0.458,0.198 10 false MR 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR 0.458,2.448 0.917,2.646 0.458,0.198 10 false E 2.646,3.052 3.104,3.25 0.458,0.198 10 false MAT 0.719,2.031 1.177,2.229 0.458,0.198 10 false ILL- 2.906,2.594 3.365,2.792 0.458,0.198 10 false ILL+
*1 Mirror Retract Switch
*2 Mirror Adjust Switch
*3 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11(MAT) - 9(E)
12(MR) - 9(E) 		Return position 10 kΩ or higher
11(MAT) - 9(E) AUTO position Below 1 Ω
12(MR) - 9(E) Retract position Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

w/ illumination:

Check that the LED illuminates.

i.

Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → 10 (ILL+)
Auxiliary battery negative (-) → 22 (ILL-) 		Illuminates


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (for GTMC Made)

a.
B525839C03
2.125,0.75 2.625,0.75 true 1.917,1.177 2.667,1.177 true 2.063,1.552 2.563,1.552 true 0.583,3 1.042,2.708 true 1.406,3.052 1.49,2.719 true 0.865,3.042 1.281,2.708 true 1.083,3 1.396,2.708 true 1.688,3.063 1.635,2.688 true 2.167,3 2.167,2.667 true 2.458,3.031 2.292,2.698 true 2.708,3.052 2.417,2.667 true 0.583,2.521 0.917,2.521 true 1.938,3.052 1.938,2.719 true 1.177,2.646 1.177,2.135 1.177,2.135 1.01,2.135 true 2.531,2.677 2.865,2.677 true 2.667,0.677 2.979,0.833 0.313,0.156 10 false *1 2.688,1.094 3,1.25 0.313,0.156 10 false *2 2.615,1.469 2.927,1.625 0.313,0.156 10 false *3 0.354,1.844 0.667,2 0.313,0.156 10 false *a 2.385,3.063 2.844,3.26 0.458,0.198 10 false MR 2.125,3.063 2.583,3.26 0.458,0.198 10 false B 1.906,3.083 2.365,3.281 0.458,0.198 10 false E 1.625,3.073 2.083,3.271 0.458,0.198 10 false VR 1.313,3.073 1.771,3.271 0.458,0.198 10 false M+ 1,3.031 1.458,3.229 0.458,0.198 10 false VL 0.708,3.021 1.167,3.219 0.458,0.198 10 false HL 0.375,2.969 0.833,3.167 0.458,0.198 10 false HR 0.458,2.448 0.917,2.646 0.458,0.198 10 false E 2.646,3.052 3.104,3.25 0.458,0.198 10 false MAT 0.719,2.031 1.177,2.229 0.458,0.198 10 false ILL- 2.906,2.594 3.365,2.792 0.458,0.198 10 false ILL+
*1 Mirror Retract Switch
*2 Mirror Adjust Switch
*3 Mirror Select Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Check the mirror retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11(MAT) - 9(E)
12(MR) - 9(E) 		Return position 10 kΩ or higher
11(MAT) - 9(E) AUTO position Below 33 Ω
12(MR) - 9(E) Retract position Below 33 Ω


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror adjust switch.

i.

Select the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
20 (VL) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
20 (VL) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
21 (HL) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
21 (HL) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
18 (VR) - 13 (B)
19 (M+) - 15 (E) 		Up Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
18 (VR) - 15 (E) 		Down Below 1 Ω
Off 10 kΩ or higher
23 (HR) - 13 (B)
19 (M+) - 15 (E) 		Left Below 1 Ω
Off 10 kΩ or higher
19 (M+) - 13 (B)
23 (HR) - 15 (E) 		Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

w/ illumination:

Check that the LED illuminates.

i.

Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → 10 (ILL+)
Auxiliary battery negative (-) → 22 (ILL-) 		Illuminates


If the result is not as specified, replace the outer mirror switch assembly.