CRUISE CONTROL MILLIMETER WAVE RADAR SENSOR REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during millimeter wave radar sensor assembly removal/installation are shown below.
| Replaced Part or Performed Procedures | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Millimeter wave radar sensor assembly | Adjust millimeter wave radar sensor assembly | ·
Dynamic radar cruise control system (for HV Model) ·
Lane tracing assist system ·
Front radar sensor system ·
Pre-collision system ·
Automatic high beam system |
Driving Adjustment:
(  202304,202405,_51,_083055,_0401007,RM1000000029L6F,202405,202409,_51,_083055,_0401007,RM100000002ME7H,202409,999999,_51,_083055,_0401007,RM100000002NTD7,)
Target Adjustment (Triangle Target): ( 202304,202405,_51,_083055,_0401007,RM1000000029L6G,202405,202409,_51,_083055,_0401007,RM100000002ME7I,202409,999999,_51,_083055,_0401007,RM100000002NTD8,)
Target Adjustment (Flat Surface Target): ( 202304,202405,_51,_083055,_0401007,RM1000000029L6H,202405,202409,_51,_083055,_0401007,RM100000002ME7K,202409,999999,_51,_083055,_0401007,RM100000002NTDA,)
|
| Replaced Part or Performed Procedures | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Millimeter wave radar sensor assembly | Adjust millimeter wave radar sensor assembly | ·
Dynamic radar cruise control system (for Gasoline Model) ·
Lane tracing assist system ·
Front radar sensor system ·
Pre-collision system ·
Automatic high beam system |
Driving Adjustment:
( 202304,202405,_51,_083055,_0401007,RM1000000029L6F,202405,202409,_51,_083055,_0401007,RM100000002ME7H,202409,999999,_51,_083055,_0401007,RM100000002NTD7,)
Target Adjustment (Triangle Target): ( 202304,202405,_51,_083055,_0401007,RM1000000029L6G,202405,202409,_51,_083055,_0401007,RM100000002ME7I,202409,999999,_51,_083055,_0401007,RM100000002NTD8,)
Target Adjustment (Flat Surface Target): ( 202304,202405,_51,_083055,_0401007,RM1000000029L6H,202405,202409,_51,_083055,_0401007,RM100000002ME7K,202409,999999,_51,_083055,_0401007,RM100000002NTDA,)
|
PROCEDURE
17751
1.REMOVE NO. 1 INLET AIR CLEANER (for Gasoline Model)
53510
2.REMOVE HOOD LOCK ASSEMBLY
16681A
3.REMOVE RADIATOR UPPER AIR GUIDE PLATE
88211B
4.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
- NOTICE:
-
Do not reuse the millimeter wave radar sensor assembly if it has been dropped or subjected to a severe impact.
Disconnect the connector.
|
Bolt |
|
Screw |
Remove the 2 bolts and screw.
Detach the guide and remove the millimeter wave radar sensor assembly.