The ECM has a built-in internal temperature sensor which detects the internal temperature of the ECM. The resistance of the thermistor within the ECM internal temperature sensor changes according to the internal temperature of the ECM. The resistance of the thermistor increases as the ECM internal temperature decreases and decreases as the ECM internal temperature increases.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P06AB11 | Control Module Internal Temperature Sensor "B" Circuit Short to Ground | The ECM internal temperature sensor output voltage is less than 0.22 V for 3 seconds or more (1 trip detection logic). | ECM | Comes on | DTC stored | SAE: P06AD |
| P06AB15 | Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open | The ECM internal temperature sensor output voltage is higher than 4.91 V for 3 seconds or more (1 trip detection logic). | ECM | Comes on | DTC stored | SAE: P06AE |
The ECM calculates the internal temperature of the ECM based on the output voltage of the ECM internal temperature sensor. If the output voltage of the ECM internal temperature sensor is not within the normal operating range, the ECM will illuminate the MIL and store a DTC. In this case, the ECM internal temperature sensor may be malfunctioning or there may be an open or short in the sensor circuit.
Example:
When the output voltage of the ECM internal temperature sensor is less than 0.22 V, or more than 4.91 V for 3 seconds or more, the ECM illuminates the MIL and stores a DTC.
| Required Sensors/Components | ECM internal temperature sensor |
| Frequency of Operation | Continuous |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON [A].
Turn the GTS on.
Wait 5 seconds [B].
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P06AB11 or P06AB15.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P06AB11 or P06AB15 is output | B |
A
B