RM36D0EC _V1 General _083136 MAINTENANCE _0402919 GF2A TRANSFER OIL A

MAINTENANCE  GF2A TRANSFER OIL  REPLACEMENT  


PROCEDURE

Hide 2.DRAIN TRANSFER OIL

a.

Stop the vehicle on a level surface.


b.
C405115C01
1.833,1.76 1.667,1.76 1.667,1.76 1.667,1.208 true 1.594,0.74 2.063,0.74 true 2.125,0.656 2.354,0.854 0.229,0.198 10 true *1 1.896,1.667 2.094,1.865 0.198,0.198 10 true *2
*1 Transfer Filler Plug
*2 Transfer Drain Plug


Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


c.

Using a 10 mm hexagon socket wrench, remove the transfer drain plug and gasket and drain the transfer oil.


d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 3.ADD TRANSFER OIL

a.

Using a 10 mm straight hexagon wrench and 10 x 12 mm long offset wrench, remove the transfer filler plug and gasket.


b.

Add transfer oil.

Oil grade:

Toyota genuine differential gear oil LX


NOTICE:

Using transfer oil other than the specified oil may cause abnormal noise or vibration, or damage the transfer of your vehicle.



c.
C278961C01
2.667,0.854 2.979,1.052 0.313,0.198 10 false *a
*a 0 to 5.0 mm (0 to 0.197 in.)


Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the transfer filler plug hole.

NOTICE:
·

When adding oil, pour it slowly.

·

Add oil a little at a time, waiting several minutes between each addition of oil.

·

Too much or too little oil will lead to transfer problems.



Standard capacity:

0.36 to 0.42 liters (0.381 to 0.443 US qts, 0.317 to 0.369 Imp. qts)



d.

Wait approximately 5 minutes and check that the oil level has not changed.


e.
C405116C01
0.563,4.406 0.396,4.406 0.396,4.406 0.396,4.156 true 0.375,4 0.375,3.5 true 0.875,3.958 1,3.167 1,3.167 1.167,3.167 true 0.615,4.323 0.927,4.479 0.313,0.156 10 false *a 0.292,3.271 0.604,3.427 0.313,0.156 10 false *b 2.052,3.594 2.365,3.75 0.313,0.156 10 false *c 1.26,3.083 1.573,3.25 0.313,0.167 10 false SST
*a 10 mm Straight Hexagon Wrench
*b 10 mm Union Nut Wrench
*c Fulcrum Length


Using SST, 10 mm straight hexagon wrench and union nut wrench, install a new gasket into the transfer filler plug, and then install the transfer filler plug.

SST
09961-00950  

Torque:
Specified tightening torque : 39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

After adding oil, drive the vehicle and recheck the oil level (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(Click here)

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 150 mm (5.906 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 19.9 N*m (203 kgf*cm, 15 ft.*lbf)