DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | - | - | - | Cannot be used |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| PCS Function ON/OFF State | Pre-collision system on/off status | ON or OFF | ON: Pre-collision system on
OFF: Pre-collision system off |
- |
| PBA Request | Pre-collision brake assist operation status | Not PBA Request, PBA Standby Request, PBA Request Level 1, PBA Request Level 2 | Not PBA Request: Pre-collision brake assist not operating
PBA Standby Request: Pre-collision brake assist operating and brake pedal not depressed PBA Request Level 1: Pre-collision brake assist operating and brake pedal depressed PBA Request Level 2: Pre-collision brake assist operating and brake pedal deeply depressed |
The value varies according to the possibility of a collision. The pre-collision brake assist request only indicates the status that the assist preparation is necessary. Whether or not the assist control is actually performed is dependent upon how the driver depresses the brake pedal. |
| VGRS Activation Request | - | - | - | Cannot be used |
| Warning Brake Request | Warning brake request status | ON or OFF | ON: Warning brake request on
OFF: Warning brake request off |
Cannot be used |
| FPB Request | PCS brake request to skid control ECU (pre-collision braking) | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PB Request | Pre-collision brake operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| AVS Control Request | - | - | - | Cannot be used |
| Prefill | PCS brake operation preparation to skid control ECU | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PBR Request | PBR operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PBH Request | PBH operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PCS PBA Invalid | Pre-collision brake assist function status | ON or OFF | ON: Pre-collision brake assist function invalid
OFF: Pre-collision brake assist function valid |
- |
| PCS Warning Buzzer Invalid | PCS warning buzzer function status | ON or OFF | ON: PCS warning buzzer function invalid
OFF: PCS warning buzzer function valid |
- |
| PCS PB Invalid | PCS brake function status | ON or OFF | ON: PCS brake function invalid
OFF: PCS brake function valid |
- |
| Acceleration Suppression at Low Speed (A Control) Invalid | Acceleration suppression at low speed (A control) invalid status | ON or OFF | ON: Acceleration suppression at low speed (A control) function invalid
OFF: Acceleration suppression at low speed (A control) function valid |
Cannot be used |
| Emergency Steering Assist Invalid 1 | Emergency Steering Assist Invalid 1 status | ON or OFF | ON: Emergency steering assist invalid 1 function invalid
OFF: Emergency steering assist invalid 1 function valid |
- |
| PCS Warning Display Request | PCS warning message status | Not Request, PCS Warning Display 1 Request, PCS Warning Display 2 Request, PCS Warning Display 3 Request | Not Request: Not displayed
PCS Warning Display 1 Request: Displayed PCS Warning Display 2 Request: Not used PCS Warning Display 3 Request: Not used |
"BRAKE!" is displayed on multi-information display. |
| PCS Warning Buzzer Request | PCS meter buzzer operation status | ON or OFF | ON: PCS warning buzzer sounding
OFF: PCS warning buzzer not sounding |
- |
| Vehicle Information (Conv/HV/EV) | Vehicle information (Conv/HV/EV) | Unknown, Conv or HV/EV | Unknown: Vehicle information not confirmed
Conv: Conventional HV/EV: Hybrid vehicle |
- |
| Vehicle Information (Powertrain Type) | Vehicle information (powertrain type) | Unknown, Conv, S&S, HV, PHV, EV, 1Motor HV, FCV | - | - |
| Vehicle Information (Transmission Type) | Vehicle information (powertrain type) | MT, AT, CVT, MMT, SMT, HV/EV - AT or Unknown | Displays the type of transmission | - |
| Power Steering Control Module Equipped Information | Power steering control module is installed or not | Absence or Presence | Absence: Not equipped
Presence: Equipped |
- |
| VGRS ECU Equipped Information | Variable gear ratio steering system function availability | Unknown, Absence or Presence | Unknown: Vehicle information not confirmed
Absence: Variable gear ratio steering system absence Presence: Variable gear ratio steering system presence |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Warning Buzzer | Sounds the meter buzzer | Active / Not Active | Test possible with ignition switch ON and vehicle stopped |