DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start / Data List.
Read the Data List according to the display on the GTS
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | 0 to 16777215 | Same as actual total distance traveled | For the unit, refer to "Total Distance Traveled - Unit" |
| Total Distance Traveled - Unit | Total Distance Traveled - unit | km or mile | km: km
mile: mile |
- |
| Back Door Lock Status | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Half Latch Switch | Latch switch signal | ON or OFF | ON: Back door lock motor open-latched
OFF: Back door lock motor full-latched or half-latched |
- |
| Closer Position Switch | Initial switch signal | ON or OFF | ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off) |
- |
| Pawl Switch | Pawl switch signal | ON or OFF | ON: Back door lock motor open-latched
OFF: Back door lock motor except open latched |
- |
| Courtesy Switch | Back door courtesy switch signal | ON or OFF | ON: Back door open
OFF: Back door closed |
- |
| PBD Main Switch | Power back door ON/OFF signal | ON or OFF | Current customize setting displayed | Setting can be changed on "System Setting" on the multi-information display |
| PBD Close Switch | Power back door control switch assembly signal | ON or OFF | ON: Back door control switch assembly pushed
OFF: Back door control switch assembly not pushed |
- |
| IG Switch | Ignition switch signal | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch to ACC. |
| Kick Sensor Function | Status of the hands free power back door function* | ON or OFF | ON: Hands free power back door ON
OFF: Hands free power back door off |
- |
| Close and Lock Switch | Door control switch signal | ON or OFF | ON: Door control switch pressed
OFF: Door control switch not pressed |
- |
| Door Lock Signal | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Status of Kick Sensor Abnormal | Status of the kick door control sensor error* | Normal or Abnormal | Normal: Kick door control sensor is normal
Abnormal: Kick door control sensor is abnormal |
- |
| Kick Sensor Installation | Status of the kick door control sensor connection* | ON or OFF | ON: Kick door control sensor equipped
OFF: Kick door control sensor not equipped |
- |
| PBD Touch Sensor RH | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor LH | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Correction of Back Door Position | Correction of back door position | Not Complied With or Complied With | Not Complied With: not complied with
Complied With: complied with |
- |
| PBD SW Operating Condition Setting | Back door control switch operation | Short Press (0.04s) or Long Press (0.8s) | Current customize setting displayed | - |
| PBD Buzzer Function | Status of the power back door buzzer | ON or OFF | Current customize setting displayed | - |
| PBD Assist Close Function | Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. | ON or OFF | Current customize setting displayed | - |
| PBD Assist Open Function | Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch (open switch) is operated. | ON or OFF | Current customize setting displayed | - |
| PBD Door Unlock with One Motion Setting | Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). | Back Door or All Doors | Current customize setting displayed | - |
| PBD Wireless Function | Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). | ON or OFF | Current customize setting displayed | - |
| PBD Wireless One Motion Function | Wireless one motion function | ON or OFF | Current customize setting displayed | - |
| PBD Wireless SW Setting | Wireless operation setting condition | 1 Time Press, 2 Times Press or Long Press (0.8s) | Current customize setting displayed | - |
*: w/ Hands Free Power Back Door
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Lock Position Status | Back door lock | Unlock or Lock | Unlock: Back door locked
Lock: Back door unlocked |
- |
| Back Door Courtesy Switch Status | Back door courtesy light switch signal | Close or Open | Close: Back door closed
Open: Back door open |
- |
| Back Door Operation Switch (Instrument) | Power back door control switch signal | OFF or ON | OFF: Power back door control switch off
ON: Power back door control switch on |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch (open switch) signal | OFF or ON | OFF: Back door opener switch (open switch) off
ON: Back door opener switch (open switch) on |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door / Active Test.
Perform the Active Test according to the display on the GTS
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PBD Motor (Open) | Power back door motor operation | Start | - |
| PBD Motor (Close) | Power back door motor operation | Start | - |
| PBD Buzzer (Small Volume) | Power back door warning buzzer sound (small volume) | Start | - |
| PBD Buzzer (Middle Volume) | Power back door warning buzzer sound (Middle volume) | Start | - |
| PBD Buzzer (Large Volume) | Power back door warning buzzer sound (Large volume) | Start | - |
| PBD Release Closer | Latch release operation | Start | - |
| Courtesy Lamp | Power back door close switch light condition | Start | - |