DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Read the Data List according to the display on the GTS.
for Long Type Panoramic Fixed Moonroof
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | OFF or ON | OFF: OPEN switch not pressed
ON: OPEN switch pressed |
- |
| Close Switch | CLOSE switch signal | OFF or ON | OFF: CLOSE switch not pressed
ON: CLOSE switch pressed |
- |
| Front SW Auto Operation | Roof sunshade auto operation function | OFF or ON | Customize setting displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal
Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low
Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal
Error: Hall IC2 not normal |
- |
| Ignition (MPX) | Ignition switch signal (LIN signal) | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
- |
| Open Switch Failure(Past) | Open switch failure signal (Past) | OFF or ON | OFF: No roof sunshade open switch failure signal (Past)
ON: Roof sunshade open switch failure signal (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | OFF or ON | OFF: No roof sunshade close switch failure signal (Past)
ON: Roof sunshade close switch failure signal (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current) | OFF or ON | OFF: No roof sunshade open switch failure signal (Current)
ON: Roof sunshade open switch failure signal (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | OFF or ON | OFF: No roof sunshade close switch failure signal (Current)
ON: Roof sunshade close switch failure signal (Current) |
- |
| Number of Trouble Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of stored DTCs | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Light Control Glass Switch | Dimmable panoramic roof switch status | OFF or ON | OFF: Dimmable panoramic roof switch not pushed
ON: Dimmable panoramic roof switch pushed |
- |
| Light Control Glass Inverter Circuit | Dimmable panoramic roof glass inverter circuit status | Normal or Error | Normal: Dimmable panoramic roof glass inverter circuit normal
Error: Dimmable panoramic roof glass inverter circuit abnormal |
- |
| Communication Sunshade ECU | Roof sunshade ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) connection status | STOP or OK | STOP: Communication stopped
OK: Normal communication |
for Long Type Panoramic Fixed Moonroof |
| Light Control Glass Brightness Memory Function | Function that memorizes state of dimmable panoramic roof glass when ignition switch is turned off | Disable or Enable | Customize setting displayed | - |
| Slide Roof Voice Control Function | Voice recognition linked roof shade open/close function | Disable or Enable | Customize setting displayed | ·
for Long Type Panoramic Fixed Moonroof ·
w/ Body Device Voice Recognition Function |
| Light Control Glass Voice Control Function | Voice recognition linked dimmable panoramic roof glass dim/transparent function | Disable or Enable | Customize setting displayed | w/ Body Device Voice Recognition Function |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
for Long Type Panoramic Fixed Moonroof
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate roof sunshade motor | OFF
Opn/Dwn* Clos/Up |
- |
*: Although this item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Light Control Glass Relay | Light control glass relay operation | OFF or ON | - |
| Light Control Glass Indicator | Light control glass indicator operation | OFF or ON | - |