DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Motor Cam Switch 1 | Front wiper stop position status | OFF or ON | OFF: Front wiper not at bottom of stroke
ON: Front wiper at bottom of stroke |
- |
| Wiper Control Switch HI | Front wiper switch HI position signal | OFF or ON | OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position |
- |
| Communication Wiper ECU | Connection status between windshield wiper motor assembly and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Not Connected
OK: Connected |
Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Communication Wiper Module | Connection status between windshield wiper relay assembly and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Not Connected
OK: Connected |
DTCs are stored if a malfunction occurs in the CXPI communication system. |
| Communication Humidity/Rain Sensor | Connection status between rain sensor and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Not Connected
OK: Connected |
DTCs are stored if a malfunction occurs in the LIN communication system. |
| R Wiper Stop Function at Back Door/Trunk Lid Open | Function to enable the back door open linked rear wiper suspend function | Not Available or Available | Customize setting displayed | - |
| Rear Wiper Washer Function | Function to enable the rear washer linked rear wiper operation function | Not Available or Available | Customize setting displayed | - |
| Rear Wiper with Reverse Setting | Function to enable the R shift position linked rear wiper operation function | Not Available, Once or Continuance | Customize setting displayed | - |
| Wiper Voice Control Function | Function to enable the voice recognition function | Not Available or Available | Customize setting displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper OFF Switch | Front wiper switch OFF position signal | OFF or ON | OFF: Front wiper switch not in OFF position
ON: Front wiper switch in OFF position |
- |
| Wiper Auto/Int Switch | Front wiper switch AUTO*1 or INT*2 position signal | OFF or ON | OFF: Front wiper switch not in AUTO*1 or INT*2 position
ON: Front wiper switch in AUTO*1 or INT*2 position |
- |
| Wiper Lo Switch | Front wiper switch LO position signal | OFF or ON | OFF: Front wiper switch not in LO position
ON: Front wiper switch in LO position |
- |
| Wiper Hi Switch | Front wiper switch HI position signal | OFF or ON | OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position |
- |
| Wiper Mist Switch | Front wiper switch MIST position signal | OFF or ON | OFF: Front wiper switch not in MIST position
ON: Front wiper switch in MIST position |
- |
| Washer Switch | Washer switch Fr WASH position signal | OFF or ON | OFF: Washer switch not in Fr WASH position
ON: Washer switch in Fr WASH position |
- |
| Rear Wiper INT Switch | Rear wiper switch INT position signal | OFF or ON | OFF: Rear wiper switch not in INT position
ON: Rear wiper switch in INT position |
- |
| Rear Wiper ON Switch | Rear wiper switch Rr ON position signal | OFF or ON | OFF: Rear wiper switch not in ON position
ON: Rear wiper switch in ON position |
- |
| Rear Washer Switch | Washer switch Rr WASH position signal | OFF or ON | OFF: Washer switch not in Rr WASH position
ON: Washer switch in Rr WASH position |
- |
| Intermittent Time Volume (Shortest) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) not in P4 position
ON: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) in P4 position |
*3 |
| Intermittent Time Volume (Shorter) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) not in P3 position
ON: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) in P3 position |
*3 |
| Intermittent Time Volume (Longer) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) not in P2 position
ON: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) in P2 position |
*3 |
| Intermittent Time Volume (Longest) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) not in P1 position
ON: Windshield wiper switch assembly (auto sensitivity adjustment*1 or intermittent time adjustment*2 volume condition) in P1 position |
*3 |
| Wiper Spec Info | Specification information | Unknown, Auto spec or Int spec | Unknown: Specification not stored
Auto Spec: Automatic wiper control Int Spec: Vehicle speed sensing intermittent time adjustment control |
- |
*1: w/ Auto Wiper System
*2: w/o Auto Wiper System
*3: Refer to Inspection for each position of the switch.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sensor Info | Rain sensor temperature circuit condition | OK or NG | OK: Rain sensor is normal
NG: Malfunction in rain sensor thermistor |
w/ Auto Wiper System |
| Sensor Reaction Info | Rain sensor output condition | OK or NG | OK: Rain sensor is normal
NG: Malfunction in rain sensor thermistor output |
w/ Auto Wiper System |
| Sensor High Temp Info | Rain sensor high temperature condition | OK or NG | OK: Rain sensor is normal
NG: Rain sensor temperature is high |
w/ Auto Wiper System |
| Sensor Low Temp Info | Rain sensor low temperature condition | OK or NG | OK: Rain sensor is normal
NG: Rain sensor temperature is low |
w/ Auto Wiper System |
| Wiper Switch Auto Signal | Windshield wiper switch assembly (AUTO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in AUTO position
ON: Windshield wiper switch assembly in AUTO position |
w/ Auto Wiper System |
| Intermittent Time Volume | Auto sensitivity adjustment volume condition | Shortest, Shorter, Longer or Longest | Shortest: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P4 position
Shorter: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P3 position Longer: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P2 position Longest: Windshield wiper switch assembly (auto sensitivity adjustment volume condition) P1 position |
* |
| Wiper Type | Displays vehicle wiper type | Normal, Reversing (1 Motor) or Reversing (2 Motor) | Shows vehicle wiper type | w/ Auto Wiper System |
| Wiper Stop Position | Windshield wiper motor assembly stop position | Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos | Store Area/Lower Rev Pos: Lower reverse position or lower
Wipe Area: Between lower reverse position and upper reverse position Upper Rev Pos: Upper reverse position |
w/ Auto Wiper System |
| Wiper Stop Position (Sub Motor) | No. 2 Windshield wiper motor assembly stop position | Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos | Store Area/Lower Rev Pos: Lower reverse position or lower
Wipe Area: Between lower reverse position and upper reverse position Upper Rev Pos: Upper reverse position |
Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Motor Status | Wiper motor control condition in response to rain sensor request | Normal, Normal (Link Ctrl), Normal (Req Deny), Abnormal or Normal (Wiper Ctrl) | Current motor control condition | w/ Auto Wiper System |
| Wiping Mode Signal (Sensor to Wiper) | Status of command request signal for front wiper speed and intermittent time from rain sensor | Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop | Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (because rain not detected)
LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested Wait: Rain sensor is judging wiping mode INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction) |
w/ Auto Wiper System |
| Wiper LO Single Operation Signal | Wiper LO Single Operation Signal | ON or OFF | ON: Windshield wiper switch assembly in AUTO position and sensor determines small amount of rain while wiper is in stopped position
OFF: Windshield wiper switch assembly in AUTO position and wiper in position other than stopped |
w/ Auto Wiper System |
| Wiping Mode Signal (Wiper to Sensor) | Response status of command request signal for front wiper speed and intermittent time from rain sensor to windshield wiper motor assembly | Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop | Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (because rain not detected)
LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested Wait: Rain sensor is judging wiping mode INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction) |
w/ Auto Wiper System |
| Sensor High Temp History | History of rain sensor temperature being high (approximately 80°C (176°F)) | OFF or ON | OFF: The rain sensor temperature has not been high (approximately 80°C (176°F))
ON: The rain sensor temperature reached high (approximately 80°C (176°F)) |
Clearing the DTCs also clears the history. |
| Sensor Low Temp History | History of rain sensor temperature being low (approximately -40 °C (-40°F)) | OFF or ON | OFF: The rain sensor temperature has not been low (approximately -40°C (-40°F))
ON: The rain sensor temperature reached low (approximately -40°C (-40°F)) |
Clearing the DTCs also clears the history. |
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | w/ Auto Wiper System |
| Auto Wiper | Setting to switch control between automatic wipers/vehicle speed sensing intermittent time adjustment | Avail or Not Avl | Customize setting displayed | w/ Auto Wiper System |
| Number of Trouble Code | Number of DTCs | 0 to 255 | Number of stored DTCs displayed | w/ Auto Wiper System |
*: Refer to Inspection for each position of the switch.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Power Relay | Function to operate the IG1 WIP relay | OFF or ON | - |
| Front Washer Relay | Function to operate the windshield washer motor and pump assembly (Front) | OFF or ON | - |
| Front Wiper Lo Operation | Function to operate the windshield wiper motor assembly in LO | OFF or ON | - |
| Front Wiper Hi Operation | Function to operate the windshield wiper motor assembly in HI | OFF or ON | - |
| Rear Washer Relay | Function to operate the windshield washer motor and pump assembly (Rear) | OFF or ON | - |
| Rear Wiper Operation | Function to operate the rear wiper motor assembly | OFF or ON | - |
| Washer Nozzle Heater | Washer nozzle heater operation | OFF or ON | Not applicable |