DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | 0 to 16777215 | Same as actual total distance traveled | For the unit, refer to "Total Distance Traveled - Unit" |
| Total Distance Traveled - Unit | Total Distance Traveled - unit | km or mile | km: km
mile: mile |
- |
| Back Door Lock Status | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Half Latch Switch | Latch switch signal | ON or OFF | ON: When in the open latch or overstroke position
OFF: Half latch position → full latch position |
- |
| Closer Position Switch | Initial switch signal | ON or OFF | ON: Back door lock sector gear in center position (Initial switch on)
OFF: Back door lock sector gear out of center position (Initial switch off) |
- |
| Pawl Switch | Pawl switch signal | ON or OFF | ON: Back door lock motor open-latched
OFF: Back door lock motor except open latched |
- |
| Courtesy Switch | Back door courtesy switch signal | ON or OFF | ON: Open latch position → half latch position
OFF: Full latch position → overstroke position |
- |
| PBD Main Switch | Power back door ON/OFF signal | ON or OFF | Current customize setting displayed | - |
| PBD Close Switch | No. 1 power back door control switch signal | ON or OFF | ON: No. 1 power back door control switch pushed
OFF: No. 1 power back door control switch not pushed |
- |
| IG Switch | Ignition switch signal | ON or OFF | ON: Ignition switch ON
OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch to ACC. |
| Kick Sensor Function | Status of the hands free power back door function | ON or OFF | ON: Hands free power back door ON
OFF: Hands free power back door off |
- |
| Door Lock Signal | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Status of Kick Sensor Detection | Kick door control sensor ON detection status | ON or OFF | ON: Kick door control sensor ON detected
OFF: Kick door control sensor ON not detected |
- |
| Status of Kick Sensor Abnormal | Kick door control sensor abnormal condition | Normal or Abnormal | Normal: Kick door control sensor normal
Abnormal: Kick door control sensor abnormal |
- |
| Kick Sensor Installation | Kick door control sensor installed condition | ON or OFF | ON: Kick door control sensor incorrectly installed
OFF: Kick door control sensor correctly installed |
- |
| PBD Touch Sensor RH | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed
OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor LH | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed
OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| Correction of Back Door Position | Correction of back door position | Not Complied With or Complied With | Not Complied With: not complied with
Complied With: complied with |
- |
| PBD Close Switch Operation History | Power back door control switch operation history | ON or OFF | ON: Has operation history
OFF: No operation history |
The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds. |
| Close & Lock Switch Operation History | Back door control switch operation history | ON or OFF | ON: Has operation history
OFF: No operation history |
Although the item is displayed on the GTS, it is not applicable to this vehicle |
| Kick Sensor Status | Kick Sensor condition signal | Normal, Sensitivity Low (Noise), Stop (Foreign Objects), Sensitivity Low (Noise) & Stop (Foreign Objects), Stop (Battery Protection), Sensitivity Low (Noise) & Stop (Battery Protection), Stop (Foreign Objects) & Stop (Battery Protection) or Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection) | Normal: Kick sensor detection status normal
Sensitivity Low (Noise): Kick sensor detection sensitivity decreased due to noise Stop (Foreign Objects): Kick sensor detection stopped due to foreign objects Sensitivity Low (Noise) & Stop (Foreign Objects): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects Stop (Battery Protection): Kick sensor detection stopped due to battery protection Sensitivity Low (Noise) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to battery protection Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor detection stopped due to foreign objects and battery protection Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects and battery protection |
- |
| Opened Number of Times | Number of times for back door opened | 0 to 214783647 | Number of times for back door opened | - |
| Closed Number of Times | Number of times for back door closed | 0 to 214783647 | Number of times for back door closed | - |
| PBD SW Operating Condition Setting | Back door control switch operation | ON or 0.8s | Current customize setting displayed | - |
| PBD Buzzer Function | Status of the power back door warning buzzer | ON or OFF | Current customize setting displayed | - |
| PBD Assist Close Function | Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually. | ON or OFF | Current customize setting displayed | - |
| PBD Assist Open Function | Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated. | ON or OFF | Current customize setting displayed | - |
| PBD Door Unlock with One Motion Setting | Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). | Back Door or All Doors | Current customize setting displayed | - |
| PBD Wireless Function | Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). | ON or OFF | Current customize setting displayed | - |
| PBD Wireless One Motion Function | Wireless one motion function | ON or OFF | Current customize setting displayed | - |
| PBD Wireless SW Setting | Wireless operation setting condition | 1 Time Press, 2 Times Press or Long Press (0.8s) | Current customize setting displayed | - |
| PBD Kick Sensor Sensitivity Adjust | Function that changes the sensitivity of the kick sensor. | Normal, +1, +2 or Unknown | Current customize setting displayed | - |
| PBD Kick-in Beep Sound | Function that sounds a buzzer when a kick operation detected. | ON or OFF | Current customize setting displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Lock Position Status | Back door lock position signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Back Door Courtesy Switch Status | Back door courtesy light switch signal | Close or Open | Close: Back door closed
Open: Back door open |
- |
| Back Door Operation Switch (Instrument) | Power back door control switch signal | ON or OFF | ON: Power back door control switch on
OFF: Power back door control switch off |
- |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
According to the display on GTS perform the "Active Test".
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PBD Motor (Open) | Power back door motor operation | Start | - |
| PBD Motor (Close) | Power back door motor operation | Start | - |
| PBD Buzzer (Small Volume) | Power back door warning buzzer sound (small volume) | Start | - |
| PBD Buzzer (Middle Volume) | Power back door warning buzzer sound (Middle volume) | Start | - |
| PBD Buzzer (Large Volume) | Power back door warning buzzer sound (Large volume) | Start | - |
| PBD Release Closer | Latch release operation | Start | - |