DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch | OPEN switch signal | OFF or ON | OFF: OPEN switch on the slide switch not pressed
ON: OPEN switch on the slide switch pressed |
- |
| Close Switch | CLOSE switch signal | OFF or ON | OFF: CLOSE switch on the slide switch not pressed
ON: CLOSE switch on the slide switch pressed |
- |
| Up Switch | UP switch signal | OFF or ON | OFF: UP switch not on the tilt switch pressed
ON: UP switch on the tilt switch pressed |
- |
| Down Switch | DOWN switch signal | OFF or ON | OFF: DOWN switch on the tilt switch not pressed
ON: DOWN switch on the tilt switch pressed |
- |
| Front SW Auto Operation | Sliding roof auto operation function | OFF or ON | Customize setting displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal
Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low
Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal
Error: Hall IC2 not normal |
- |
| Ignition (MPX) | Ignition switch signal (LIN signal) | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
- |
| Door Key Close Operation | Key-linked sliding roof close signal | OFF or ON | OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the lock position |
- |
| Door Key Open Operation | Key-linked sliding roof open signal | OFF or ON | OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the unlock position |
- |
| Wireless Close Operation | Wireless transmitter-linked sliding roof close signal | OFF or ON | OFF: Electrical key transmitter sub-assembly LOCK switch not pressed
ON: Electrical key transmitter sub-assembly LOCK switch pressed and held |
- |
| Wireless Open Operation | Wireless transmitter-linked sliding roof open signal | OFF or ON | OFF: Electrical key transmitter sub-assembly UNLOCK switch not pressed
ON: Electrical key transmitter sub-assembly UNLOCK switch pressed and held |
- |
| Key Off Permission | Key-off sliding roof operation permit signal | OFF or ON | OFF: Any status except "ON" status
ON: Front doors are not opened within 45 seconds after ignition switch turned off |
- |
| Door Key Related Operation | Key-linked sliding roof open function operating direction | Slide or Tilt | Customize setting displayed | - |
| Wireless Key Rel Operation | Wireless transmitter-linked sliding roof open function operating direction | Slide or Tilt | Customize setting displayed | - |
| Open Switch Failure(Past) | Open switch failure signal (Past) | OFF or ON | OFF: No OPEN switch on the slide switch failure signal (Past)
ON: OPEN switch on the slide switch failure signal (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | OFF or ON | OFF: No CLOSE switch on the slide switch failure signal (Past)
ON: CLOSE switch on the slide switch failure signal (Past) |
- |
| Up Switch Failure(Past) | Up switch failure signal (Past) | OFF or ON | OFF: No UP switch on the tilt switch failure signal (Past)
ON: UP switch on the tilt switch failure signal (Past) |
- |
| Down Switch Failure(Past) | Down switch failure signal (Past) | OFF or ON | OFF: No DOWN switch on the tilt switch failure signal (Past)
ON: DOWN switch on the tilt switch failure signal (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current) | OFF or ON | OFF: No OPEN switch on the slide switch failure signal (Current)
ON: OPEN switch on the slide switch failure signal (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | OFF or ON | OFF: No CLOSE switch on the slide switch failure signal (Current)
ON: CLOSE switch on the slide switch failure signal (Current) |
- |
| Up Switch Failure(Current) | Up switch failure signal (Current) | OFF or ON | OFF: No UP switch on the tilt switch failure signal (Current)
ON: UP switch on the tilt switch failure signal (Current) |
- |
| Down Switch Failure(Current) | Down switch failure signal (Current) | OFF or ON | OFF: No DOWN switch on the tilt switch failure signal (Current)
ON: DOWN switch on the tilt switch failure signal (Current) |
- |
| Suggestion Service Function | Availability of suggestion function* | OFF or ON | ON: w/ Suggestion function
OFF: w/o Suggestion function |
Not applicable |
| Number of Trouble Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of stored DTCs | - |
*: Although this item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy Switch Status | Front door courtesy light switch assembly RH signal | Close or Open | Close: Front door RH closed
Open: Front door RH open |
- |
| FL Door Courtesy Switch Status | Front door courtesy light switch assembly LH signal | Close or Open | Close: Front door LH closed
Open: Front door LH open |
- |
| Communication Slide Roof | Connection status between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
| Door Key P/W Up Function | Key-linked sliding roof close function | Disable or Enable | Customize setting displayed | - |
| Door Key P/W Down Function | Key-linked sliding roof open function | Disable or Enable | Customize setting displayed | - |
| P/W Up W/ Transmit Function | Wireless transmitter linked sliding roof close function | Disable or Enable | Customize setting displayed | - |
| P/W Down W/ Transmit Function | Wireless transmitter linked sliding roof open function | Disable or Enable | Customize setting displayed | - |
| Slide Roof Open Warning Function | Sliding roof open warning function | Disable or Enable | Customize setting displayed | - |
| Slide Roof Voice Control Function | Status of slide roof open/close linked voice recognition control | Disable or Enable | Customize setting displayed | - |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof motor | OFF / Opn/Dwn / Clos/Up | - |