RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0417478 REAR BUMPER(for Type B) A

EXTERIOR PANELS / TRIM REAR BUMPER(for Type B) REASSEMBLY

PROCEDURE

Hide Display 52023 1.INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (for Type A)>REASSEMBLY202304,999999,_59,_083111,_0400752,RM1000000029RQZ_01_0323,

Hide Display 52188A 2.INSTALL REAR BUMPER ARM REINFORCEMENT LH

Attach the claw and guide and install the rear bumper arm reinforcement LH.

Hide Display 52187A 3.INSTALL REAR BUMPER ARM REINFORCEMENT RH

HINT:: Use the same procedure described for the LH side.

Hide Display 52156A 4.INSTALL REAR BUMPER SIDE SUPPORT LH

0,0 0,0 false

Install in this Direction

Attach the guide and claw to install the rear bumper side support LH.

Attach the clip.

Install the 2 screws.

Hide Display 52155A 5.INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:: Use the same procedure described for the LH side.

Hide Display 52563A 6.INSTALL REAR BUMPER UPPER RETAINER LH

0,0 0,0 false

Install in this Direction

Attach the guide and install the rear bumper upper retainer LH to the rear combination light assembly LH.

Hide Display 52562B 7.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:: Use the same procedure described for the LH side.

Hide Display 8.INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

0,0 0,0 false

	Place Hand Here
	Install in this Direction

Place your hands at the position shown in the illustration, pass the wire harness into the vehicle and install the grommet.

1.396,0.833 1.542,1.021 0.146,0.188 10 true *a 0.854,1.052 1.031,1.219 0.177,0.167 10 true *b

*a	Pin
*b	Guide
	Push in this Direction

Align the guide and pin to set the rear combination light assembly LH.

Push the rear combination light assembly LH towards the vehicle front to attach the pin and guide.

Install the 2 screws.

Install the 2 screws.

Insert your hand between the deck trim side panel assembly LH and the body and connect the connector.

Hide Display 9.INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

HINT:: Use the same procedure described for the LH side.

Hide Display 64740E 10.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Return the rear side of the deck trim side panel assembly LH to its original position.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0057,

Hide Display 64730J 11.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Return the rear side of the deck trim side panel assembly RH to its original position.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0012,

Hide Display 58460D 12.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0018,

Hide Display 58386 13.INSTALL REAR FLOOR FINISH PLATE

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0037,

Hide Display 65351A 14.INSTALL BATTERY HOLE COVER (for HV Model)

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0074,

Hide Display 58417H 15.INSTALL REAR NO. 3 FLOOR BOARD

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0042,

Hide Display 58416K 16.INSTALL REAR NO. 2 FLOOR BOARD

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION202304,999999,_58,_083106,_0400609,RM1000000029RSX_01_0040,

Hide Display 52463B 17.INSTALL REAR BUMPER FRONT PAD LH

HINT:: When installing the rear bumper front pad LH, heat the rear bumper piece LH and rear bumper front pad LH using a heat light.

Standard:

Item	Temperature
Rear Bumper Piece LH	20 to 30°C (68 to 86°F)
Rear Bumper Front Pad LH	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper front pad LH excessively.

When reusing the rear bumper piece LH:

Using a heat light, heat the rear bumper piece LH surface.

ii.

Remove any remaining double-sided tape from the rear bumper piece LH.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper front pad LH with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new rear bumper piece LH surface.

1.104,3.406 1.531,3.406 true 0.865,3.344 1.031,3.521 0.167,0.177 10 true *a

*a	Mark-off Line
	Primer

Apply primer to the rear bumper piece LH on the installation area of the rear bumper front pad LH using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper front pad LH has been attached.

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Using a heat light, heat the rear bumper piece LH and a new rear bumper front pad LH.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper front pad LH excessively.

Remove the release paper of the new rear bumper front pad LH trying not to touch the adhesional surface.

NOTICE:: After removing the release paper, keep the exposed adhesive free from foreign matter.

1.188,3.448 1.51,3.448 false 1.01,3.354 1.177,3.542 0.167,0.188 10 true *a

*a	Mark-off Line

Align the rear bumper front pad LH with the mark-off line on the rear bumper piece LH and install it.

NOTICE:: The application strength of the rear bumper front pad LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Press the rear bumper front pad LH firmly to install it.

Hide Display 52463B 18.INSTALL REAR BUMPER FILLER PAD LH

HINT:: When installing the rear bumper filler pad LH, heat the rear bumper piece LH and rear bumper filler pad LH using a heat light.

Standard:

Item	Temperature
Rear Bumper Piece LH	20 to 30°C (68 to 86°F)
Rear Bumper Filler Pad LH	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper filler pad LH excessively.

When reusing the rear bumper piece LH:

Using a heat light, heat the rear bumper piece LH surface.

ii.

Remove any remaining double-sided tape from the rear bumper piece LH.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper filler pad LH with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new rear bumper piece LH surface.

0.927,3.458 1.323,3.458 true 0.667,3.365 0.865,3.583 0.198,0.219 10 true *a

*a	Mark-off Line
	Primer

Apply primer to the rear bumper piece LH on the installation area of the rear bumper filler pad LH using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper filler pad LH has been attached.

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Using a heat light, heat the rear bumper piece LH and a new rear bumper filler pad LH.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper filler pad LH excessively.

Remove the release paper of the new rear bumper filler pad LH trying not to touch the adhesional surface.

NOTICE:: After removing the release paper, keep the exposed adhesive free from foreign matter.

0.979,3.458 1.333,3.458 false 0.792,3.375 0.969,3.542 0.177,0.167 10 true *a

*a	Mark-off Line

Align the rear bumper filler pad LH with the mark-off line on the rear bumper piece LH and install it.

NOTICE:: The application strength of the rear bumper filler pad LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Press the rear bumper filler pad LH firmly to install it.

Hide Display 52463 19.INSTALL REAR BUMPER PAD LH

HINT:: When installing the rear bumper pad LH, heat the rear bumper piece LH and rear bumper pad LH using a heat light.

Standard:

Item	Temperature
Rear Bumper Piece LH	20 to 30°C (68 to 86°F)
Rear Bumper Pad LH	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper pad LH excessively.

When reusing the rear bumper piece LH:

Using a heat light, heat the rear bumper piece LH surface.

ii.

Remove any remaining double-sided tape from the rear bumper piece LH.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper pad LH with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new rear bumper piece LH surface.

2.135,3.406 2.448,3.406 true 2.5,3.323 2.688,3.51 0.188,0.188 10 true *a

*a	Mark-off Line
	Primer

Apply primer to the rear bumper piece LH on the installation area of the rear bumper pad LH using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad LH has been attached.

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Using a heat light, heat the rear bumper piece LH and a new rear bumper pad LH.

NOTICE:: Do not heat the rear bumper piece LH and rear bumper pad LH excessively.

Remove the release paper of the new rear bumper pad LH trying not to touch the adhesional surface.

NOTICE:: After removing the release paper, keep the exposed adhesive free from foreign matter.

2.135,3.333 2.448,3.333 true 2.49,3.25 2.677,3.438 0.188,0.188 10 true *a

*a	Mark-off Line

Align the rear bumper pad LH with the mark-off line on the rear bumper piece LH and install it.

NOTICE:: The application strength of the rear bumper pad LH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Press the rear bumper pad LH firmly to install it.

Hide Display 52462 20.INSTALL REAR BUMPER PAD RH

HINT:: When installing the rear bumper pad RH, heat the rear bumper piece RH and rear bumper pad RH using a heat light.

Standard:

Item	Temperature
Rear Bumper Piece RH	20 to 30°C (68 to 86°F)
Rear Bumper Pad RH	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper piece RH and rear bumper pad RH excessively.

When reusing the rear bumper piece RH:

Using a heat light, heat the rear bumper piece RH surface.

ii.

Remove any remaining double-sided tape from the rear bumper piece RH.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper pad RH with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new rear bumper piece RH surface.

2.198,3.719 1.74,3.719 true 2.26,3.625 2.417,3.823 0.156,0.198 10 true *a

*a	Mark-off Line
	Primer

Apply primer to the rear bumper piece RH on the installation area of the rear bumper pad RH using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper pad RH has been attached.

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Using a heat light, heat the rear bumper piece RH and a new rear bumper pad RH.

NOTICE:: Do not heat the rear bumper piece RH and rear bumper pad RH excessively.

Remove the release paper of the new rear bumper pad RH trying not to touch the adhesional surface.

NOTICE:: After removing the release paper, keep the exposed adhesive free from foreign matter.

2.198,3.719 1.74,3.719 true 2.26,3.625 2.417,3.823 0.156,0.198 10 true *a

*a	Mark-off Line

Align the rear bumper pad RH with the mark-off line on the rear bumper piece RH and install it.

NOTICE:: The application strength of the rear bumper pad RH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Press the rear bumper pad RH firmly to install it.

Hide Display 52462C 21.INSTALL REAR BUMPER FRONT PAD RH

HINT:: When installing the rear bumper front pad RH, heat the rear bumper piece RH and rear bumper front pad RH using a heat light.

Standard:

Item	Temperature
Rear Bumper Piece RH	20 to 30°C (68 to 86°F)
Rear Bumper Front Pad RH	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper piece RH and rear bumper front pad RH excessively.

When reusing the rear bumper piece RH:

Using a heat light, heat the rear bumper piece RH surface.

ii.

Remove any remaining double-sided tape from the rear bumper piece RH.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper front pad RH with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Clean a new rear bumper piece RH surface.

1.917,3.302 2.313,3.302 true 2.354,3.208 2.542,3.396 0.188,0.188 10 true *a

*a	Mark-off Line
	Primer

Apply primer to the rear bumper piece RH on the installation area of the rear bumper front pad RH using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper front pad RH has been attached.

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Using a heat light, heat the rear bumper piece RH and a new rear bumper front pad RH.

NOTICE:: Do not heat the rear bumper piece RH and rear bumper front pad RH excessively.

Remove the release paper of the new rear bumper front pad RH trying not to touch the adhesional surface.

NOTICE:: After removing the release paper, keep the exposed adhesive free from foreign matter.

1.938,3.385 2.271,3.385 true 2.302,3.302 2.479,3.49 0.177,0.188 10 false *a

*a	Mark-off Line

Align the rear bumper front pad RH with the mark-off line on the rear bumper piece RH and install it.

NOTICE:: The application strength of the rear bumper front pad RH will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Press the rear bumper front pad RH firmly to install it.

Hide Display 76829A 22.INSTALL BACK DOOR GARNISH RETAINER

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (for Type A)>REASSEMBLY202304,999999,_59,_083111,_0400752,RM1000000029RQZ_01_0313,

Hide Display 52461F 23.INSTALL REAR BUMPER CENTER PAD

HINT:: When installing the rear bumper center pad, heat the rear bumper cover using a heat light.

Standard:

Item	Temperature
Rear Bumper Cover	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the rear bumper cover excessively.

When reusing the rear bumper cover:

Using a heat light, heat the rear bumper cover surface.

ii.

Remove any remaining double-sided tape from the rear bumper cover.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the rear bumper center pad with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean the surface of the new rear bumper cover.

Apply primer to the rear bumper cover on the installation area of the rear bumper center pad using a brush or felt.

NOTICE:: ·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear bumper center pad has been attached.

3.573,0.823 3.573,0.271 true 2.24,0.813 3.573,0.25 3.573,0.25 4.906,0.802 true 3.51,0.042 3.823,0.24 0.313,0.198 10 false *a

*a	Mark-off Line	-	-
	Primer	-	-

Let the primer dry sufficiently.

NOTICE:: Do not touch applied surfaces until the primer is dry.

Recommended drying time:: 10 minutes or more (at 23°C (73°F))

Remove the release paper of the new rear bumper center pad trying not to touch the adhesional surface.

HINT:: After removing the release paper, keep the exposed adhesive free from foreign matter.

Align the rear bumper center pad with the mark-off line on the rear bumper cover and install it.

HINT:: Press the rear bumper center pad firmly to install it.

3.573,0.823 3.573,0.271 true 2.24,0.813 3.573,0.25 3.573,0.25 4.906,0.802 true 3.51,0.042 3.823,0.24 0.313,0.198 10 false *a

Mark-off Line

Hide Display 52751C 24.INSTALL REAR BUMPER MOULDING

0,0 0,0 false

Install in this Direction

Attach the guide and claw and install the rear bumper moulding as shown in the illustration.

Install the 3 screws.

Hide Display 81920 25.INSTALL REFLEX REFLECTOR ASSEMBLY LH

0,0 0,0 false

Install in this Direction

Attach the guide and claw and install the reflex reflector assembly LH.

Install the 2 screws.

Hide Display 81910 26.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:: Use the same procedure described for the LH side.

Hide Display 81480A 27.INSTALL REAR FOG LIGHT ASSEMBLY

Click hereVehicle Exterior>LIGHTING (EXT)>REAR FOG LIGHT ASSEMBLY>INSTALLATION202004,999999,_59,_083096,_0403540,RM100000001MODI_02_0003,

Hide Display 28.INSTALL SPRING NUT

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER (for Type A)>REASSEMBLY202304,999999,_59,_083111,_0400752,RM1000000029RQZ_01_0306,

Hide Display 52162A 29.INSTALL REAR BUMPER PIECE LH

0,0 0,0 false

Install in this Direction

Attach the guide and claw to install the rear bumper piece LH.

Install the 3 outside moulding retainers.

Install the 2 screws.

Hide Display 52161A 30.INSTALL REAR BUMPER PIECE RH

HINT:: Use the same procedure described for the LH side.

Hide Display 891B1 31.INSTALL KICK DOOR CONTROL BRACKET (w/ Hands Free Power Back Door)

Click hereVehicle Exterior>DOOR / HATCH>KICK SENSOR>INSTALLATION202304,999999,_59,_083093,_0417406,RM1000000029SB3_01_0002,

Hide Display 89C48B 32.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION202405,202409,_56,_083082,_0403105,RM100000002KZ0L_01_0041,202409,999999,_56,_083082,_0403105,RM100000002OUBE_01_0041,

Hide Display 89C48A 33.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION202405,202409,_56,_083082,_0403105,RM100000002KZ0L_01_0033,202409,999999,_56,_083082,_0403105,RM100000002OUBE_01_0033,

Hide Display 89342A 34.INSTALL REAR CENTER ULTRASONIC SENSOR

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION202405,202409,_56,_083082,_0403105,RM100000002KZ0L_01_0034,202409,999999,_56,_083082,_0403105,RM100000002OUBE_01_0034,

Hide Display 89342 35.INSTALL REAR CORNER ULTRASONIC SENSOR

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Rear)>INSTALLATION202405,202409,_56,_083082,_0403105,RM100000002KZ0L_01_0035,202409,999999,_56,_083082,_0403105,RM100000002OUBE_01_0035,

Hide Display 82182 36.INSTALL NO. 2 LUGGAGE ROOM WIRE

Attach the clamp to install the No. 2 luggage room wire.

Connect each connector.

NOTICE:: Do not apply excessive loads to the retainer. Otherwise, it may peel off.

4.833,2.823 5.063,3.031 0.229,0.208 12 true *A

w/ Hands Free Power Back Door