RM36D0EC _51 Engine / Hybrid System _083058 M20D-FKS ENGINE CONTROL _0401818 THROTTLE BODY A

M20D-FKS ENGINE CONTROL THROTTLE BODY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during throttle body with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
· Replacement of throttle body with motor assembly · Cleaning the deposits from the throttle body with motor assembly	Inspection after repair	· Poor idle, etc. · Engine start function, etc.	(202304,202409,_51,_083058,_0401834,RM1000000029C6V,202409,999999,_51,_083058,_0401834,RM100000002NA8M,)

NOTICE:: This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.; Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION201910,999999,_V1,_083040,_0402303,RM100000001JHCH,

PROCEDURE

Hide Display 1.DRAIN ENGINE COOLANT

Click hereGeneral>MAINTENANCE>M20D-FKS COOLANT>REPLACEMENT201910,999999,_V1,_083136,_0403615,RM100000001JU0H_02_0001,

Hide Display 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Click hereEngine / Hybrid System>M20D-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL202304,202405,_51,_083059,_0403046,RM1000000029XAE_01_0288,202405,202409,_51,_083059,_0403046,RM100000002JNSM_01_0288,202409,999999,_51,_083059,_0403046,RM100000002NRBV_01_0288,

Hide Display 17751 3.REMOVE NO. 1 INLET AIR CLEANER

Remove the 2 bolts and No. 1 inlet air cleaner.

Hide Display 4.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Disconnect the mass air flow meter sub-assembly connector.

Detach the 3 wire harness clamps.

2.49,4.302 2.49,3.677 true 2.313,4.302 2.313,3.333 true 2.833,4.292 1.844,4.292 1.844,4.292 1.844,3.917 true 2.875,4.177 3.125,4.385 0.25,0.208 10 false *a

Disconnect the vacuum hose from the air cleaner hose.

Slide the clip and disconnect the No. 2 PCV hose from the cylinder head cover sub-assembly.

Loosen the hose clamp and disconnect the air cleaner hose from the throttle body with motor assembly.

Pull out the air cleaner assembly with air cleaner hose 3 pins from the air cleaner support.

Hide Display 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Disconnect the throttle body with motor assembly connector.

Slide the clip and disconnect the No. 8 water by-pass hose from the throttle body with motor assembly.

Remove the 3 bolts and disconnect the throttle body with motor assembly from the intake manifold.

Slide the clip and disconnect the No. 5 water by-pass hose to remove the throttle body with motor assembly.

NOTICE:: If the throttle body with motor assembly has been struck or dropped, replace it.

Remove the throttle body gasket from the intake manifold.