DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Head Up Display / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Current total driving distance | 0 to 16777215[km/h] | Equivalent to the actual total driving distance | - |
| Total Distance Traveled - Unit | - | - | - | Cannot be used |
| +B Voltage | Battery voltage | 0 to 25.4 [V] | 11 to 14 V | Engine switch off |
| Illumination Rate from Illuminance Sensor | Light control sensor input value | 0 to 65535 [lx] | Value according to the brightness is output | 0 is displayed when there is no light |
| Vehicle Speed Meter | Vehicle speed input value | 0 to 255 [km/h] | Almost the same as actual vehicle speed | - |
| Engine RPM | Engine speed | 0 to 12700 [r/min] | Almost the same as actual tachometer | - |
| Brightness Up Switch | Brightness up switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Brightness Down Switch | Brightness down switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Projection Position Up Switch | Projection position up switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Projection Position Down Switch | Projection position down switch | OFF or ON | OFF: Switch released
ON: Switch pushed |
This item can be inspected by adjusting a setting in the HUD settings of the settings tab displayed on the multi-information display. |
| Display Angle | Display angle of headup display | -12.7 to 12.7 [deg] | Current display angle of headup display | ·
Approximately-12.7 deg: vehicle rear ·
Approximately- 0 deg: center ·
Approximately12.7 deg: vehicle front |
| Ambient Temperature (Celsius) | Outside temperature (Celsius) | -40 to 87 [°C] | Almost the same as actual outside temperature | - |
| Ambient Temperature (Fahrenheit) | Outside temperature (Fahrenheit) | -40 to 215 [°F] | Almost the same as actual outside temperature | - |
| Illumination Rate from Light Control Sensor | - | 0 to 65535 [lx] | - | - |
| LDA System | Availability of lane tracing assist system | With or Without | With: Vehicle equipped with lane tracing assist system
Without: Vehicle not equipped with lane tracing assist system |
- |
| PCS System | Availability of pre-collision system | With or Without | With: Vehicle equipped with pre-collision system
Without: Vehicle not equipped with pre-collision system |
- |
| ICS System | - | - | - | Cannot be used |
| Radar Cruise System | Availability of dynamic radar cruise control system | With or Without | With: Dynamic radar cruise control system
Without: Dynamic radar cruise control system |
- |
| Road Sign Assist System | - | - | - | Cannot be used |
| ITS System | - | - | - | Cannot be used |
| HV System Indicator | Hybrid system indicator value | -101 to 511 [%] | Current hybrid system indicator status displayed | - |
| Navigation System | Availability of navigation system | With or Without | With: Vehicle equipped with navigation system
Without: Vehicle not equipped with navigation system |
- |
| FCTA System | - | - | - | Cannot be used |
| LTC System | - | - | - | Cannot be used |
| LCS System | - | - | - | Cannot be used |
| LVN System | - | - | - | Cannot be used |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Head Up Display / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Color Test Screen (Black) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (White) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (Red) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (Green) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (Blue) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (Color Bars) | Displays each color on headup display | OFF or ON | - |
| Color Test Screen (Adjustment) | Displays each color on headup display | OFF or ON | - |
| Display Brightness | Changes the brightness of headup display | 0 to 100 [%] | - |
| Display Position | Move the position of headup display | Up (+3)/Up (+2)/Up (+1)/Center/Down (-1)/Down (-2)/Down (-3) | - |