RM36D0EC _58 Vehicle Interior _083100 SUPPLEMENTAL RESTRAINT SYSTEMS _0400494 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS SPIRAL CABLE INSPECTION

PROCEDURE

Hide Display 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:: ·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.

Visually check the spiral cable sub-assembly for defects.

The defects are as follows:

Scratches

Small cracks

Dents

Chips

Cracks or other damage to the connector

OK:: No defects are found.

If any of the defects is found, replace the spiral cable sub-assembly with a new one.

Check the spiral cable sub-assembly.

5.552,0.698 5.802,0.865 0.25,0.167 1.635,2.885 1.969,3.052 0.333,0.167 1.49,1.281 1.656,1.448 0.167,0.167 0.385,3.656 0.719,3.823 0.333,0.167 2.021,0.208 2.271,0.375 0.25,0.167 3.24,0.208 3.49,0.375 0.25,0.167 1.167,4.417 1.76,3.698 true 1.958,3.698 2.292,3.76 true 1.958,3.792 2.292,3.938 true 1.958,3.885 2.292,4.115 true 1.958,3.594 2.292,3.594 true 1.958,3.49 2.292,3.406 true 1.958,3.396 2.292,3.229 true 0.823,4.417 1.76,3.594 true 1.417,3.083 1.76,3.385 true 1.5,4.417 1.76,3.792 true 1.792,3.927 1.792,4.417 true 0.75,3.25 1.094,3.469 true 0.75,3.438 1.094,3.656 true 0.667,4 1.094,3.833 true 0.667,4.188 1.094,4.021 true 5.604,0.698 5.917,0.896 0.313,0.198 10 false z6 1.667,2.885 1.979,3.083 0.313,0.198 10 false G20 1,4.427 1.313,4.625 0.313,0.198 10 false AU2 2.323,3.677 2.635,3.875 0.313,0.198 10 false AU1 0.635,4.427 0.948,4.625 0.313,0.198 10 false EAU 2.323,3.313 2.75,3.531 0.427,0.219 10 false +DP2 2.323,3.5 2.75,3.719 0.427,0.219 10 false +DP 1.115,2.979 1.427,3.177 0.313,0.198 10 false ECC 2.323,3.865 2.635,4.063 0.313,0.198 10 false CCS 1.531,1.281 1.844,1.479 0.313,0.198 10 false A 1.698,4.427 2.01,4.625 0.313,0.198 10 false HO 2.323,3.146 2.75,3.365 0.427,0.219 10 false IL-2 2.323,4.042 2.75,4.26 0.427,0.219 10 false IL+2 1.344,4.427 1.656,4.625 0.313,0.198 10 false DIST 0.417,3.656 0.729,3.854 0.313,0.198 10 false G21 0.563,3.146 0.875,3.344 0.313,0.198 10 false D+ 0.563,3.333 0.875,3.531 0.313,0.198 10 false D- 2.073,0.208 2.385,0.406 0.313,0.198 10 false z3 3.292,0.208 3.604,0.406 0.313,0.198 10 false z4 0.406,3.917 0.719,4.115 0.313,0.198 10 false D2- 0.406,4.104 0.719,4.302 0.313,0.198 10 false D2+ 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a

*a	Component without harness connected (Spiral Cable Sub-assembly)	-	-
	Interlock	-	-

NOTICE:: ·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

Set the spiral cable sub-assembly to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION201910,202004,_58,_083100,_0400494,RM100000001J8C6_01_0062,202004,202104,_58,_083100,_0400494,RM100000001MOWH_01_0062,202104,202304,_58,_083100,_0400494,RM100000001WOY2_01_0062,202304,202405,_58,_083100,_0400494,RM1000000029RS1_01_0062,202405,202409,_58,_083100,_0400494,RM100000002LW6I_01_0062,202409,999999,_58,_083100,_0400494,RM100000002NG0A_01_0062,

ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.

iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
G20-2 (ECC) - z6-12	Always	3 Ω or less
G20-4 (EAU) - z6-10	Always	3 Ω or less
G20-5 (AU2) - z6-9	Always	3 Ω or less
G20-6 (DIST) - z6-8	Always	3 Ω or less
G20-7 (HO) - A	Always	3 Ω or less
G20-9 (IL-2) - z6-6	Always	3 Ω or less
G20-10 (+DP2) - z6-5	Always	3 Ω or less
G20-11 (+DP) - z6-4	Always	3 Ω or less
G20-12 (AU1) - z6-3	Always	3 Ω or less
G20-13 (CCS) - z6-2	Always	3 Ω or less
G20-14 (IL+2) - z6-1	Always	3 Ω or less
G21-1 (D+) - z3-2	Always	Below 1.3 Ω
G21-2 (D-) - z3-1	Always	Below 1.3 Ω
G21-3 (D2-) - z4-1	Always	Below 1.3 Ω
G21-4 (D2+) - z4-2	Always	Below 1.3 Ω

If the result is not as specified, replace the spiral cable sub-assembly.