RM3660EC _58 Vehicle Interior _080741 SUPPLEMENTAL RESTRAINT SYSTEMS _0600231 INSPECTION AFTER COLLISION G

SUPPLEMENTAL RESTRAINT SYSTEMS INSPECTION AFTER COLLISION INSPECTION

PROCEDURE

Hide Display 1. INSPECTION AFTER COLLISION

a.

Inspect the SRS parts in table below.

CAUTION:: ·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (except NR Series Engine)>PRECAUTION202304,999999,_58,_080741,_0584471,RM1000000029GQF,

·

Be sure to correctly follow the removal and installation procedures for the SRS parts.

NOTICE:: If there is any damage or deformation of airbag installation components or the areas they are installed to, do not attempt to repair them. Replace the damaged components with new ones.

Component to Inspect	Procedure
Horn button assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the horn button assembly removed from the vehicle. HINT: The defects are as follows: · The airbag has deployed · Cuts on the surface or in the grooves · Small cracks on the surface or in the grooves · Significant discoloration on the surface or in the grooves · Cracks or other damage to the connector · Deformation of the steering wheel assembly · Deformation of the installation surface of the horn button assembly · Interference or uneven clearance between the horn button assembly and steering wheel assembly when a new horn button assembly is installed to the steering wheel assembly OK: No defects are found. If any defects are found, replace the horn button assembly or steering wheel assembly with a new one.
Instrument panel passenger airbag assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the instrument panel passenger airbag assembly removed from the vehicle. HINT: The defects are as follows: · The airbag has deployed · Cuts · Small cracks · Significant discoloration · Cracks or other damage to the connector · Deformation or cracks on the instrument panel safety pad sub-assembly or instrument panel reinforcement assembly OK: No defects are found. If any defects are found, replace the instrument panel passenger airbag assembly, instrument panel safety pad sub-assembly or instrument panel reinforcement assembly with a new one.
Curtain shield airbag assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the curtain shield airbag assemblies removed from the vehicle. HINT: The defects are as follows: · The airbag has deployed · Cuts · Small cracks · Significant discoloration · Cracks or other damage to the connector OK: No defects are found. If any defects are found, replace the curtain shield airbag assembly with a new one.
Front seat airbag assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the front seat airbag assemblies removed from the vehicle. HINT: The defects are as follows: · The airbag has deployed · Scratches, broken or frayed threads on the surface of the base fabric of the front seat airbag assemblies · Marks from being dropped · Deformation of the installation surface of the front seat airbag assemblies · Cracks or other damage to the wire harness or connector OK: No defects are found. If any defects are found, replace the front seat airbag assembly with a new one.
Front seat outer belt assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the front seat outer belt assembly removed from the vehicle. HINT: The defects are as follows: · The seat belt pretensioner has deployed · Cuts · Small cracks · Significant discoloration · Cracks or other damage to the connector OK: No defects are found. If any defects are found, replace the front seat outer belt assembly with a new one.
Rear 3 point type seat outer belt assembly	1. Perform a diagnostic system check. 2. Visually check for defects with the rear 3 point type seat outer belt assembly removed from the vehicle. HINT: The defects are as follows: · The seat belt pretensioner has deployed · Cuts · Small cracks · Significant discoloration · Cracks or other damage to the connector OK: No defects are found. If any defects are found, replace the rear 3 point type seat outer belt assembly with a new one.
Airbag sensor with ECU assembly	1. for Airbag that has not Deployed: (a) Perform a diagnostic system check. (b) Visually check for defects with the airbag sensor with ECU assembly installed to the vehicle. HINT: The defects are as follows: · Cracks on the sensor housing · Dents on the sensor housing · Chips on the sensor housing · Cracks or other damage to the connector · Peeling of the label OK: No defects are found. If any defects are found, replace the airbag sensor with ECU assembly with a new one. 2. for Airbag that has Deployed: (a) Replace the airbag sensor with ECU assembly. HINT: The airbag sensor with ECU assembly should be replaced after any of the SRS parts has deployed, as it has been subjected to an impact.
Front airbag sensor	1. Perform a diagnostic system check. 2. When airbags have deployed as the result of a collision, be sure to replace all airbag sensors in the damaged areas (anywhere in need of repair). 3. Visually check the airbag sensors in undamaged areas for defects. HINT: The defects are as follows: · Cracks in the sensor housing · Dents in the sensor housing · Chips in the sensor housing · Cracks or other damage to the connector · Damage to the serial number · Damage to the waterproof rubber seal OK: No defects are found. If any defects are found or an airbag sensor has detected a major collision, replace the airbag sensor with a new one.
Side airbag pressure sensor
Side No. 2 airbag sensor
Harness and connector	1. Perform a diagnostic system check. 2. Check any wire harnesses in exposed contact with the airbag wire harness for damage. 3. Check the connector of the airbag wire harness for scratches, cracks or damage.