RM3660EC _54 Brake _080740 PARKING BRAKE _0394663 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  C060962  Electric Parking Brake Switch Signal Compare Failure  


DESCRIPTION

When the electric parking brake switch is pulled, a lock request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060962 Electric Parking Brake Switch Signal Compare Failure
·

Open or short detected in parking brake switch circuit for 1 second or more

·

Stuck parking brake switch detected (when parked: 30 seconds, when driving: 1 second, during engine stall: 1 second)

·

Stuck parking brake switch detected 3 times in succession when being operated


·

Electric parking brake switch assembly

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Vehicle is stopped - - - - -
Vehicle is being driven - - - - -
During initial check - - - - -
Parking brake switch is being operated - - - - -
Malfunction Status Open detected in parking brake switch circuit - - - - -
Short detected in parking brake switch circuit - - - - -
Stuck parking brake switch detected - -
Detection Time 1 second or more 1 second or more 30 seconds or more 1 second or more 1 second or more -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 3 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.READ VALUE USING GTS (EPB SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Chassis / Brake/EPB / Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EPB Switch Electric parking brake switch input Neutral / Apply / Release / Unknown Neutral: Lock switch and release switch are off
Apply: Lock switch on
Release: Release switch on
When not normal, electric parking brake switch release side system may be malfunctioning
HINT:

EPB stands for electric parking brake.


Chassis > Brake/EPB > Data List
Tester Display
EPB Switch
50003 435 142

d.

Operate the electric parking brake switch and check that the value of "EPB Switch" in the Data List changes between Apply and Release in accordance with the operation of the switch.

OK:

The value of EPB Switch changes between Apply and Release in accordance with switch operation.



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

4.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435
Result:
Proceed to
NEXT




NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the I183 electric parking brake switch assembly connector.


b.

Disconnect the A144 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A144-31 (SWI1) - I183-7 (SWI1) Always Below 1 Ω
A144-32 (SWO1) - I183-8 (SWO1) Always Below 1 Ω
A144-15 (SWI2) - I183-1 (SWI2) Always Below 1 Ω
A144-16 (SWO2) - I183-2 (SWO2) Always Below 1 Ω
A144-31 (SWI1) or I183-7 (SWI1) - Body ground Always 10 kΩ or higher
A144-32 (SWO1) or I183-8 (SWO1) - Body ground Always 10 kΩ or higher
A144-15 (SWI2) or I183-1 (SWI2) - Body ground Always 10 kΩ or higher
A144-16 (SWO2) or I183-2 (SWO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the power switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC
a.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B