DCM OPERATION HISTORY
This function is used to display operation history information and the time at which it was stored in the telematics transceiver.
When problem symptoms due to wave interference cannot be reproduced, this function provides telematics transceiver operation history information which can be used to explain the cause of the malfunction to the customer.
Check DCM Operation History
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / DCM Operation History
| Tester Display |
|---|
| DCM Operation History |
Choose "Items" on the DCM Operation History Menu.
When "Operation Code" is recorded, DCM Operation History is displayed on the GTS.
The displayed "Function" differs depending on the selected "Items".
Refer to the following chart and check the system operation status displayed on the GTS. (The following chart is an example of the system operation status.)
| Occurrence Time*1 | Operation Code*2 | Function*3 | Content*4 | Roaming*5 | Voice Call*6 | Service Area*7 | Electric Level*8 |
|---|---|---|---|---|---|---|---|
| 2017/12/31 12:40:50 | 0101 | GNSS (Satellite) | Unreceived GNSS (Satellite) signal | ON | With | Out of Service | Level 0 |
| Tester Display | Description | Range | ||
|---|---|---|---|---|
| *1 | Occurrence time | Indicates date of the telematics transceiver operation. | - | |
| *2 | Operation Code | Indicates the Operation Code. | - | |
| *3 | Function | Items | Indicates the function name. | - |
| Common | ·
GNSS (Satellite) ·
Collision Detection ·
Network Power Supply Control ·
SMS ·
Telematics PF ·
Failure Due to Conflict ·
Activate Function |
|||
| Emergency Call | ·
Emergency Call ·
Automatic Maintenance ·
Manual Maintenance |
|||
| Remote Diagnostics | ·
Remote Warning ·
Remote DTC / FFD ·
Remote Monitoring ·
Remote Vehicle History ·
Remote DTC / FFD on IP ·
Remote Monitoring on IP |
|||
| Center Request | Center Request Command | |||
| Remote Service | ·
Maintenance Assistance ·
Remote Diagnostics Recorder ·
Remote Confirmation ·
Under Repair Rejection ·
Last File |
|||
| Remote Control | ·
Remote Control ·
Remote Hazard ·
Remote Door Lock ·
Remote Power Window ·
Pre Air-Conditioning |
|||
| Security | ·
Alarm Notification ·
Remote Immobilizer ·
Stolen Vehicle Tracking ·
Remote Vehicle Tracking |
|||
| Operation Monitor | Operation Monitoring | |||
| Network | ·
Air Data Feed ·
APN Selection ·
TSC Client Authentication ·
Simple HTTP Proxy 1 ·
Simple HTTP Proxy 2 ·
Simple HTTP Proxy 3 ·
Simple HTTP Proxy 4 ·
Simple HTTP Proxy 5 ·
Simple HTTP Proxy 6 ·
Simple HTTP Proxy 7 ·
Simple HTTP Proxy 8 |
|||
| Vehicle Information | ·
Vehicle Info. CAN ·
Vehicle Info. Ethernet |
|||
| *4 | Content | Indicates the content. | - | |
| *5 | Roaming | Indicates whether roaming was used for the communication network. | ON or OFF | |
| *6 | Voice Call | Indicates whether there was a voice call. | With or Without | |
| *7 | Service Area | Indicates whether the vehicle was in the service area. | Out of Service, Within Range, OFF the Air or Start up (LTE) | |
| *8 | Electric Level | Indicates the strength of the cellular signal received by the vehicle. | Level 0, Level 1, Level 2, Level 3, Level 4, Level 5 | |
ALL READINESS
With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.
You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs even if no DTCs are stored.
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON.
Perform the DTC judgment driving pattern to run the DTC judgment.
Enter the following menus: Body Electrical / Telematics / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC to be confirmed.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
|
If the judgment result shows Incomplete or N/A, perform the DTC confirmation driving pattern again. |
|
| Normal | ·
DTC judgment completed ·
System normal |
| Abnormal | ·
DTC judgment completed ·
System abnormal |
| Incomplete | ·
DTC judgment not completed ·
Perform the driving pattern |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit ·
Perform the driving pattern |
Turn the ignition switch off.
CANCEL COMMUNICATION FUNCTION PAUSING
This function is used to display Cancel Communication Function Pausing
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / Cancel Communication Function Pausing.
| Tester Display |
|---|
| Cancel Communication Function Pausing |
ACN CALL END
The mobilephone battery must not be replaced while an ACN call is in progress.
This function terminates the ACN (Automatic Collision Notification) to the telematics provider. After a collision in which the DCM receives "Collision Detection Signal", the vehicle will send the emergency call notification to the telematics provider until the emergency call cancellation utility has been run, or the mobilephone battery (if equipped) is depleted. Use the emergency call cancellation utility to stop the ACN call.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Telematics / Utility / Emergency Call Cancellation.
| Tester Display |
|---|
| Emergency Call Cancellation |
Follow the instructions on the GTS.