DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
Body Electrical / Main Body / Data List.
Chassis / Steering Angle Sensor / Data List.
Body Electrical / Combination Meter / Data List.
w/ Automatic High Beam System:
Body Electrical / Front Recognition Camera (Front Lighting Control) / Data List.
w/ Automatic High Beam System:
Chassis / Front Recognition Camera / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Parking Brake SW | Parking brake switch signal | OFF or ON | OFF: Parking brake switch off
ON: Parking brake switch on |
- |
| Auto High Beam Main Switch | Auto high beam switch signal*1 | OFF or ON | OFF: Auto high beam switch not pressed
ON: Auto high beam switch pressed |
- |
| Head Light SW (Head) | Light control switch HEAD position signal | OFF or ON | OFF: Light control switch not in HEAD position
ON: Light control switch in HEAD position |
- |
| Insolation Amount of Solar Sensor RH | Solar sensor RH condition*2 | 0 to 51100 or SensorFail | Condition can be displayed | - |
| Insolation Amount of Solar Sensor LH | Solar sensor LH condition*2 | 0 to 51100 or SensorFail | Condition can be displayed | - |
| Light Sensor Illuminance | Light control sensor illuminance*2 | 0 to 8191 lx or SensorFail | Value is output according to ambient light level | - |
| Light Sensor Connection Status | Light control sensor connection status | OFF or ON | OFF: Automatic light control sensor has not been connected
ON: Automatic light control sensor connected or has been connected |
- |
| Headlight Lighting Function | ECU which controls the lighting system | Main Body or Lighting Sys ECU | Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)
Lighting Sys ECU: Lighting system is controlled by headlight ECU sub-assembly |
- |
| Response Time | Delay timing of lighting the taillights when the automatic light control sensor detects brightness change | 0.1 s or 1.0 s | Customize setting displayed | - |
| Sensitivity | Sensitivity of the automatic light control system*2 | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex ON Sen | Ambient brightness level required to dim display lights (combination meter, navigation display, etc.)*2 | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Disp Ex OFF Sen | Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.)*2 | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | - |
| Light Auto OFF Delay | Light auto OFF delay*3 | Off, 30 s, 60 s or 90 s | Customize setting displayed | - |
| Auto H Beam STS0 | Automatic high beam sensor current state*1 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning. |
| Auto H Beam STS1 | Automatic high beam sensor state past 1 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS2 | Automatic high beam sensor state past 2 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS3 | Automatic high beam sensor state past 3 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS4 | Automatic high beam sensor state past 4 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS5 | Automatic high beam sensor state past 5 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS6 | Automatic high beam sensor state past 6 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Auto H Beam STS7 | Automatic high beam sensor state past 7 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err | Condition can be displayed*6 | Although this item is displayed on the GTS, it is not applicable to this vehicle. |
| Extended Headlight Lighting | Sets the headlight lighting time after the ignition switch is turned off*4 | 30 s, 60 s, 90 s, or 120 s | Customize setting displayed | - |
| Tail Remind Buzzer Function | Setting of the tail remind buzzer function on/off | OFF or ON | Customize setting displayed | - |
| Auto Light Off Timing Setting | Sets the timing to turn off the taillights when the light control switch is in the TAIL or HEAD position.*5 | IG OFF or Door Open | Customize setting displayed | - |
| The Number of DTC | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
*1: w/ Automatic High Beam System
*2: w/ Automatic Light Control System
*3: w/ Delay Function
*4: w/ Extended Headlight Lighting
*5: for vehicles with customize setting "Auto Light Off Timing setting"
*6: The details of each value of the Range are as follows:
| Display Value | Condition | Control Condition | Diagnostic Note |
|---|---|---|---|
| Undetec | Automatic high beam sensor being initialized | Control suspended (low beam headlights illuminated) | - |
| CAM NA | Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. | Control suspended (low beam headlights illuminated) | - |
| No sens | No lights detected | High beam headlights illuminated | Only when vehicle speed within operation speed range |
| Hlight | Headlights of oncoming vehicle, etc. detected | Low beam headlights illuminated | Only when vehicle speed within operation speed range |
| Taillgt | Taillights preceding vehicle, etc. detected | Low beam headlights illuminated | Only when vehicle speed within operation speed range |
| Speed | No lights detected and vehicle speed below operation speed | Low beam headlights illuminated | - |
| Daytime | Bright light detected | Low beam headlights illuminated | - |
| Village | Streetlights, etc. detected | Low beam headlights illuminated | Only when vehicle speed within operation speed range |
| Delay | Changing between low beams and high beams | Changing between low beams and high beams | Only when vehicle speed within operation speed range |
| SAE Mod | Not applicable | - | - |
| Malfunc | |||
| Aim Lmt | |||
| Undefin | |||
| LIN Err |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Light OFF Switch | Light control switch OFF position signal*1 | OFF or ON | OFF: Light control switch not in OFF position
ON: Light control switch in OFF position |
- |
| Auto Light Switch | Light control switch AUTO position signal*2 | OFF or ON | OFF: Light control switch not in AUTO position
ON: Light control switch in AUTO position |
- |
| Head Light Switch (Tail) | Light control switch TAIL position signal | OFF or ON | OFF: Light control switch not in TAIL position
ON: Light control switch in TAIL position |
- |
| Head Light Switch (Head) | Light control switch HEAD position signal | OFF or ON | OFF: Light control switch not in HEAD position
ON: Light control switch in HEAD position |
- |
| High Beam Main Switch | Headlight dimmer switch High position signal | OFF or ON | OFF: Headlight dimmer switch not in High position
ON: Headlight dimmer switch in High position |
- |
| Passing Light Switch | Headlight dimmer switch Flash position (pass) signal | OFF or ON | OFF: Headlight dimmer switch not in Flash position
ON: Headlight dimmer switch in Flash position |
- |
| Auto High Beam Main Switch | Auto high beam switch signal | OFF or ON | OFF: Auto high beam switch off
ON: Auto high beam switch on |
Although the item is displayed on the GTS, it is not applicable to the vehicle. |
| Turn Signal Switch (Right) | Turn signal switch (right turn position) signal | OFF or ON | OFF: Turn signal switch not in right turn position
ON: Turn signal switch in right turn position |
- |
| Turn Signal Switch (Left) | Turn signal switch (left turn position) signal | OFF or ON | OFF: Turn signal switch not in left turn position
ON: Turn signal switch in left turn position |
- |
| Cornering Light/Front Side Illuminate Light Switch | Turn signal switch (full turn) signal | OFF or ON | OFF: Turn signal switch not in left or right full turn position
ON: Turn signal switch in left or right full turn position |
- |
| Front Fog Light Switch | Fog light switch (front position) signal*3 | OFF or ON | OFF: Fog light switch in OFF position
ON: Fog light switch in Fr position |
- |
| Rear Fog Light/Bad Weather Switch | Fog light switch (rear position) signal*4 | OFF or ON | OFF: Fog light switch in OFF position
ON: Fog light switch in Rr position |
- |
| Automatic Light Equipped Info | Automatic light control system specification information | Unknown, With or Without | Unknown: Specification not stored
With: Automatic light control system equipped Without: Automatic light control system not equipped |
- |
| Bad Weather Mode Equipped Info | Bad weather specification information | Unknown, Without or With | Unknown: Specification not stored
Without: Bad weather specification not equipped With: Bad weather specification equipped |
Although the item is displayed on the GTS, it is not applicable to the vehicle. |
| The Number of DTCs | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
*1: w/ Light Control Switch OFF Position
*2: w/ Automatic Light Control System
*3: w/ Front Fog Light
*4: w/ Rear Fog Light
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Hazard Flasher Switch | Hazard warning signal switch signal | OFF or ON | OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on |
- |
| Lane Change Flashing Times Adjust | Condition of the lane change flashing times | OFF, 3, 4, 5, 6 or 7 | Customize setting displayed | - |
w/ Automatic High Beam System:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Actual driving distance | 0 to 16777215 | Roughly the same as the actual driving distance | - |
| Total Distance Traveled - Unit | Actual driving distance unit | km or mile | Displays the current actual driving distance unit | - |
| AHB/AHS Information | Lighting system state | unknown, AHB or AHS | Displays lighting system state | - |
w/ Automatic High Beam System:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Recognition Camera High Temperature 2 | Whether high temperature malfunction of forward recognition camera exists or not | Not High Temperature or High Temperature | Not High Temperature: Approximately 65°C (149°F) or less
High Temperature: Approximately 65°C (149°F) or higher |
If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.
|
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus:
Body Electrical / Main Body / Active Test.
Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime running lights*1 | OFF or ON | - |
| Taillight Relay | Taillight relay | OFF or ON | - |
| Headlight Relay | Low beam headlights | OFF or ON | - |
| Head Light Hi | High beam headlights | OFF or ON | - |
| Front Fog Light Relay | Front fog light relay*2 | OFF or ON | Light control switch in TAIL position |
| Rear Fog Light Relay | Rear fog light relay*3 | OFF or ON | Light control switch in TAIL position |
| Dimmer Signal | Dimmer signal | OFF or ON | State where circumference illumination is bright |
| Automatic High Beam Switch Light | Auto high beam switch indicator light*4 | OFF or ON | - |
*1: w/ Daytime Running Light
*2: w/ Front Fog Light
*3: w/ Rear Fog Light
*4: w/ Automatic High Beam System
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam Indicator (Green) | Automatic high beam indicator* | OFF or ON | - |
*: w/ Automatic High Beam System