RM35X0E _58 Vehicle Interior _078381 LIGHTING (INT) _0398445 BACK DOOR COURTESY SWITCH(for Wagon) G

LIGHTING (INT)  BACK DOOR COURTESY SWITCH(for Wagon)  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH

a.
B540145C01
1.938,2.583 2.271,2.438 true 1.948,2.771 2.281,2.917 true 1.052,2.24 1.448,2.531 0.396,0.292 10 false *a 2.375,2.875 2.76,3.177 0.385,0.302 10 false M+ 2.344,2.354 2.74,2.646 0.396,0.292 10 false M-
*a Component without harness connected
(Back Door Lock Assembly With Courtesy Light Switch)


Check the operation of the back door lock assembly with courtesy light switch.

i.

Apply battery voltage and check the operation of the closer motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (M-)
Battery negative (-) → Terminal 4 (M+) 		Open Operation
Battery positive (+) → Terminal 4 (M+)
Battery negative (-) → Terminal 1 (M-) 		Close Operation


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



b.

Check the resistance of the back door lock assembly with courtesy light switch.

B540146C01
0.531,1.51 0.875,1.281 true 1.302,1.323 1.667,1.469 true 2.938,1.531 3.281,1.302 true 3.656,1.302 3.948,1.479 true 5.219,1.5 5.563,1.271 true 5.979,1.302 6.24,1.438 true 3.646,2.052 4.021,1.927 true 3.656,2.219 4.031,2.469 true 3.052,2.396 3.417,2.219 true 3,2.063 3.385,2.063 true 0.323,1.448 0.75,1.667 0.427,0.219 10 false *1 1.75,1.417 2.073,1.625 0.323,0.208 10 false *2 0.302,0.406 0.719,0.698 0.417,0.292 10 false *a 2.677,0.448 3.031,0.781 0.354,0.333 10 false *b 5.042,0.438 5.406,0.729 0.365,0.292 10 false *c 3.042,1.792 3.354,2.094 0.313,0.302 10 false *d 2.729,1.479 3.156,1.698 0.427,0.219 10 false *1 5.021,1.448 5.448,1.667 0.427,0.219 10 false *1 4.01,1.448 4.344,1.708 0.333,0.26 10 false *2 6.302,1.427 6.646,1.656 0.344,0.229 10 false *2 4.115,1.833 4.771,2.188 0.656,0.354 10 false CLS 2.906,2.323 3.563,2.677 0.656,0.354 10 false E 4.104,2.438 4.76,2.792 0.656,0.354 10 false OPN 2.698,1.99 3.354,2.344 0.656,0.354 10 false CTY
*1 Back Door Lock Hook *2 Back Door Lock Ratchet
*a Open-latch Position *b Half-latch Position
*c Full-latch Position *d Component without harness connected
(Back Door Lock Assembly With Courtesy Light Switch)


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
HALF / FULL SWITCH
Tester Connection Condition Specified Condition
2 (CLS) - 6 (E) Open-latch Position → Half-latch position Below 1 Ω → 10 kΩ or higher
2 (CLS) - 6 (E) Half-latch position → Full latch Position 10 kΩ or higher
2 (CLS) - 6 (E) Full latch Position 10 kΩ or higher

COURTESY SWITCH
Tester Connection Condition Specified Condition
3 (CTY) - 6 (E) Open-latch Position Below 1 Ω
3 (CTY) - 6 (E) Half-latch position → Full latch Position Below 1 Ω → 10 kΩ or higher
3 (CTY) - 6 (E) Full latch Position 10 kΩ or higher

INITIAL POSITION SWITCH
Tester Connection Condition Specified Condition
5 (OPN) - 6 (E) Open-latch Position → Half-latch position 10 kΩ or higher → Below 1 Ω
5 (OPN) - 6 (E) Half-latch position → Full latch Position Below 1 Ω
5 (OPN) - 6 (E) Full latch Position Below 1 Ω


If the result is not as specified, replace the back door lock assembly with courtesy light switch.



Hide 69690 2.INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

a.

Check the operation of the back door remote control assembly.

B540147C01
5.438,1.917 5.646,1.458 true 6.135,1.917 5.885,1.469 true 5.052,1.406 5.448,1.406 true 6.083,1.396 6.479,1.396 true 3.104,1.896 3.469,2.125 0.365,0.229 10 false *a 4.135,1.76 4.458,1.958 0.323,0.198 10 false *b 5.031,0.792 5.385,1.021 0.354,0.229 10 false *c 5.25,1.969 5.865,2.167 0.615,0.198 10 false ACT+ 6.01,1.969 6.625,2.167 0.615,0.198 10 false ACT- 4.896,1.344 5.792,1.677 0.896,0.333 10 false E 6.552,1.323 6.969,1.542 0.417,0.219 10 false S
*a Direction of Lock Operation *b Direction of Unlock Operation
*c Component without harness connected
(Back Door Remote Control Assembly) 		- -


i.

Apply battery voltage and check the operation of the closer motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 3 (ACT+)
Battery negative (-) → Terminal 2 (ACT-) 		Lock Operation
Battery positive (+) → Terminal 2 (ACT-)
Battery negative (-) → Terminal 3 (ACT+) 		Unlock Operation


If the result is not as specified, replace the back door remote control assembly.



b.

Check the resistance of the back door control switch assembly (w/ Back Door Control Switch Assembly).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (S) - 4 (E) Lock 10 kΩ or higher
1 (S) - 4 (E) Unlock Below 1 Ω


If the result is not as specified, replace the back door remote control assembly.