RM35X0E _58 Vehicle Interior _078381 LIGHTING (INT) _0380033 LIGHTING SYSTEM D

LIGHTING (INT) LIGHTING SYSTEM OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:: Perform this inspection with the customize parameters at the initial settings.; Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS201906,202310,_58,_078381,_0380033,RM100000001IFRJ,202310,999999,_58,_078381,_0380033,RM100000002G3KN,

HINT:

Perform this inspection with the door switch is turned on.

Lights Controlled by Illuminated Entry System
Control	Condition	Lights that Operate
1: w/o Overhead Console 2: w/ Overhead Console 3: w/ Immobiliser System 4: w/ No. 1 Room Light for Center 5: w/o Immobiliser System 6: w/ Step Light for LED Type 7: w/ Step Light for Bulb Type 8: w/ Back Door Inside Handle Light 9: for Wagon 10: except Wagon
Actuation Area-linked*9	With the ignition switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination)
Door Lock/Unlock-linked*9	With the ignition switch off and all of the doors closed and locked, unlock any door using an unlock operation (key-linked or wireless operation) and check that the lights that operate turn on for 15 seconds and then turn off.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination)
Door Lock/Unlock-linked*10	w/ Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked or wireless operation) and check that the lights that operate turn on for 15 seconds and then turn off.	w/ Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil*3
Door Lock/Unlock-linked*10	w/o Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed and locked, unlock any door using an unlock operation (key-linked or wireless operation) and check that the lights that operate turn on for 15 seconds and then turn off.	w/o Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)4 · No. 1 room light assembly (for Rear)
Door Open/Close-linked*9	With the ignition switch off and all of the doors closed, open back door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination)
	With the ignition switch off and all the doors closed, open the front door and check that the blinking interval for the lights listed on the right slows down. After this, check that the blinking interval for the lights listed on the right quickens when the brake pedal is depressed.	Push start switch
	With the ignition switch off and all of the doors closed, open either rear door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination)
Door Open/Close-linked*10	w/ Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	w/ Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · Key cylinder light assembly5
	w/ Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed, open back door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	w/ Ignition Linked Automatic Door Unlock Function · No. 1 interior illumination light assembly LH6 · No. 1 interior illumination light assembly RH6 · No. 2 room light assembly7 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)4 · No. 1 room light assembly (for Rear) · Back door inside handle bezel*8
	w/o Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed, open any door, slide door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	w/o Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · Key cylinder light assembly5
	w/o Ignition Linked Automatic Door Unlock Function With the ignition switch off and all of the doors closed, open either rear door and check that the lights that operate turn ON. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	w/o Ignition Linked Automatic Door Unlock Function · No. 1 interior illumination light assembly LH6 · No. 1 interior illumination light assembly RH6 · No. 2 room light assembly*7
Push Start Switch-linked*9	Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination) · Push start switch
Push Start Switch-linked*9	Check that the blinking interval for the lights listed on the right slows down when the ignition switch is turned from ACC or ON to off.	Push start switch
Ignition Switch-linked*10	Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.	w/ Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 w/o Ignition Linked Automatic Door Unlock Function · Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)*4 · No. 1 room light assembly (for Rear)

INSPECT BATTERY SAVING CONTROL OPERATION

The operations and conditions of this control are described below.

Control	Condition	Lights that Operate
1: w/o Overhead Console 2: w/ Overhead Console 3: w/ Immobiliser System 4: w/ No. 1 Room Light for Center 5: w/o Immobiliser System 6: w/ Step Light for LED Type 7: w/ Step Light for Bulb Type 8: w/ Back Door Inside Handle Light 9: w/ Ignition Linked Automatic Door Unlock Function 10: w/o Ignition Linked Automatic Door Unlock Function *11: for Wagon
Basic operation*9	When 30 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 30 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON. · Front door is opened and closed. · Back door is opened and closed. · Any door is unlocked. · Room light switch is turned to on.	· Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · No. 1 interior illumination light assembly LH6 · No. 1 interior illumination light assembly RH6 · No. 2 room light assembly7 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)4 · No. 1 room light assembly (for Rear) · Back door inside handle bezel8
Basic operation*10	When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON. · Any door is opened and closed. · Any door is unlocked.	· Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)4 · No. 1 room light assembly (for Rear)
Basic operation*11	When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON. · Any door is opened and closed. · Any door is unlocked.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination) · Push start switch
Interior light auto cut operation*9	When 30 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 30 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON.	· Map light assembly1 · Map light sub-assembly2 · Transponder key coil3 · Key cylinder light assembly5
Interior light auto cut operation*10	When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON.	· Map light assembly1 · Map light sub-assembly2 · Key cylinder light assembly5 · No. 1 interior illumination light assembly LH6 · No. 1 interior illumination light assembly RH6 · No. 2 room light assembly7 · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center)*4 · No. 1 room light assembly (for Rear)
Interior light auto cut operation*11	When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or ON.	· Map light sub-assembly · No. 1 room light assembly (for Front) · No. 1 room light assembly (for Center) · No. 1 room light assembly (for Rear) · No. 1 interior illumination light assembly (Slide Door Illumination) · No. 2 interior illumination light assembly (Slide Door Illumination) · No. 1 interior illumination light assembly (Quarter Trim Illumination) · No. 2 interior illumination light assembly (Quarter Trim Illumination) · Push start switch · Step light assembly LH · Step light assembly RH

CHECK INTERIOR ILLUMINATION LIGHT (SLIDE DOOR ILLUMINATION, QUARTER TRIM ILLUMINATION) CONTROL OPERATION (for Wagon with Color Change Function)

Interior Illumination Light Color Selection Operation

HINT:: The interior illumination light color selection illuminates the lights below.; ·

No. 1 interior illumination light assembly (Slide Door Illumination)

·

No. 2 interior illumination light assembly (Slide Door Illumination)

·

No. 1 interior illumination light assembly (Quarter Trim Illumination)

·

No. 2 interior illumination light assembly (Quarter Trim Illumination)

Press the No. 2 room light switch assembly or integration control and panel assembly (No. 2 room light switch) and check that 3 colors can be chosen from for the interior illumination light.

CHECK SPOT LIGHT ASSEMBLY CONTROL OPERATION (for Wagon)

With the light off, press the spot light assembly (spot light switch) and check that the spot light assembly illuminates.

With the light illuminated, press the spot light assembly (spot light switch) and check that the brightness of the spot light assembly switches between 3 levels.

With the light illuminated, press and hold the spot light assembly (spot light switch) and check that the spot light assembly turns off.