DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | State of the blind spot monitor system | OFF or ON | OFF: Blind spot monitor system off
ON: Blind spot monitor system on |
- |
| RCTA Switch Status | State of RCTA function | OFF or ON | OFF: RCTA function off
ON: RCTA function on |
- |
| Warning Indicator Turning on(Master) | State of the outer rear view mirror indicator LH turning on | OFF or ON | OFF: Any state except "ON"
ON: Either of the following states ·
During initial check ·
Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch not on |
- |
| Warning Indicator Flashing(Master) | State of the outer rear view mirror indicator LH flashing | OFF or ON | OFF: Any state except "ON"
ON: Blind spot monitor system on, vehicle detected on left hand side and left turn signal switch on |
- |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA |
- |
| Turn Switch State | State of the turn signal switch | Left ON, Right ON or OFF | Left ON: Left turn signal switch on
Right ON: Right turn signal switch on OFF: Turn signal switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | OFF: Shift position in any other than R
ON: Shift position in R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) | Almost same as actual vehicle speed | - |
| Steering Angle | Steering angle sensor | Min.: -3072 deg, Max.: 3070.5 deg | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 49.951 V | Ignition switch ON:
10.5 to 16 V (w/ Stop and Start System) 11 to 14 V (w/o Stop and Start System) |
- |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed |
- |
| HV Flag | Hybrid vehicle | OFF or ON | OFF: Non-hybrid vehicle
ON: Hybrid vehicle |
- |
| VGRS Flag | VGRS installed | OFF or ON | OFF: VGRS not installed
ON: VGRS installed |
- |
| Beam Axis Inspection Completeness Flag | Completion of beam axis adjustment | Incompl or Compl | Incompl: Adjustment not completed
Compl: Adjustment completed |
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished |
| Destination Undefined Flag | Destination determination | Unfixed or Fixed | Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -180 deg, Max.: Over 180 deg | Angle adjusted using auto alignment is displayed | - |
| RCTA Equipped Information | State of the RCTA equipped information | OFF or ON | OFF: RCTA function off
ON: RCTA function on |
- |
| Master Side RCTA Function | Switches the RCTA function on and off | OFF or ON | OFF: RCTA function off
ON: RCTA function on |
- |
| Mirror LED Control Frequency | Frequency of the outer rear view mirror indicator on the outer mirror when blinking | Min.: 1500 Hz, Max.: 2400 Hz | Always: 2000 Hz | - |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking | Min.: 0%, Max.: 100% | Always: 50% | - |
| Yaw Rate Sensor | Yaw rate sensor | Min.: Under -124.928 deg/s, Max.: 124.684 deg/s | Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s |
- |
| BSM Mirror Indicator Brightness | Brightness of the indicators in the outer rear view mirror assemblies | Dark or Bright | Dark: Outer mirror indicator brightness low
Bright: Outer mirror indicator brightness high |
- |
| Mounting FHL Function | Installation condition of automatic rear flashing hazard lights function | Without or With | With: w/ automatic rear flashing hazard lights function
Without: w/o automatic rear flashing hazard lights function |
- |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0
When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Warning Indicator Turning on(Slave) | State of the outer rear view mirror indicator RH turning on | OFF or ON | OFF: Any state except "ON"
ON: Either of the following states ·
During initial check ·
Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch not on |
- |
| Warning Indicator Flashing(Slave) | State of the outer rear view mirror indicator RH flashing | OFF or ON | OFF: Any state except "ON"
ON: Blind spot monitor system on, vehicle detected on right hand side and right turn signal switch on |
- |
| Buzzer Sound Status | State of the RCTA buzzer (blind spot monitor buzzer) | OFF or ON | OFF: Buzzer not sounding
ON: Buzzer sounding |
- |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V
Indicator not illuminated: Below 1 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA
Indicator not illuminated: 0 mA |
- |
| Buzzer Input Circuit Voltage | RCTA buzzer (blind spot monitor buzzer) voltage | Min.: 0 V, Max.: 25.5 V | Buzzer not sounding: 11 to 14 V
Buzzer sounding: Alternating between 0 to 14 V |
- |
| Turn Switch State | State of the turn signal switch | Left ON, Right ON or OFF | Left ON: Left turn signal switch on
Right ON: Right turn signal switch on OFF: Turn signal switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | OFF: Shift position in any position except R
ON: Shift position in R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) | Almost same as actual vehicle speed | - |
| Steering Angle | Steering angle sensor | Min.: -3072 deg, Max.: 3070.5 deg | Left turn: Increases
Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 49.951 V | Ignition switch ON:
10.5 to 16 V (w/ Stop and Start System) 11 to 14 V (w/o Stop and Start System) |
- |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed
Dim ON: Indicator dimmed |
- |
| HV Flag | Hybrid vehicle | OFF or ON | OFF: Non-hybrid vehicle
ON: Hybrid vehicle |
- |
| VGRS Flag | VGRS installed | OFF or ON | OFF: VGRS not installed
ON: VGRS installed |
- |
| Beam Axis Inspection Completeness Flag | Completion of beam axis adjustment | Incompl or Compl | Incompl: Adjustment not completed
Compl: Adjustment completed |
Changes to "Compl" when blind spot monitor beam axis adjustment has been finished |
| Destination Undefined Flag | Destination determination | Unfixed or Fixed | Unfixed: Sensor destination information not determined
Fixed: Sensor destination information determined according to CAN destination information |
- |
| Buzzer Connection | State of the RCTA buzzer (blind spot monitor buzzer) | Valid or Invalid | Valid: Buzzer connected
Invalid: Buzzer not connected |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -180 deg, Max.: Over 180 deg | Angle adjusted using auto alignment is displayed | - |
| RCTA Equipped Information | Status of the RCTA equipped information | OFF or ON | OFF: RCTA function off
ON: RCTA function on |
- |
| Slave Side RCTA Function | Switches the RCTA function on and off | OFF or ON | OFF: RCTA function off
ON: RCTA function on |
- |
| Mirror LED Control Frequency | Frequency of the outer rear view mirror indicator on the outer mirror when blinking | Min.: 1500 Hz, Max.: 2400 Hz | Always: 2000 Hz | - |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking | Min.: 0%, Max.: 100% | Always: 50% | - |
| Buzzer Control Frequency | Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding | Min.: 1000 Hz, Max.: 2400 Hz | Always: 2000 Hz | - |
| Yaw Rate Sensor | Yaw rate sensor | Min.: Under -124.928 deg/s, Max.: 124.684 deg/s | Turning right: -124.928 to 0 deg/s
Turning left: 0 to 124.684 deg/s |
- |
| BSM Buzzer Volume Adjust | Volume of the RCTA buzzer (blind spot monitor buzzer) | Low, Medium or High | Low: Buzzer volume less than that of medium
Medium: Default buzzer volume High: Buzzer volume more than that of medium |
- |
| Mounting FHL Function | Installation condition of automatic rear flashing hazard lights function | Without or With | With: w/ automatic rear flashing hazard lights function
Without: w/o automatic rear flashing hazard lights function |
- |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0
When a malfunction is detected: More than 0 |
- |