RM35X0E _59 Vehicle Exterior _079318 WINDOW / GLASS _0384709 POWER WINDOW REGULATOR MOTOR G

WINDOW / GLASS POWER WINDOW REGULATOR MOTOR INSPECTION

PROCEDURE

Hide Display 69820 1.INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY LH

NOTICE:: ·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION201902,201906,_59,_079318,_0384706,RM100000001GHZN,201906,999999,_59,_079318,_0384706,RM100000001II57,

1.198,3.49 1.615,3.49 true 1.115,3.771 1.531,3.771 true 1.917,3.479 2.333,3.479 true 1.948,3.781 2.365,3.781 true 1.646,1.594 0.781,2.25 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 2.115,2.115 2.427,2.271 0.313,0.156 10 false *b 2.917,1.26 3.229,1.417 0.313,0.156 10 false *c 0.625,2.198 0.938,2.354 0.313,0.156 10 false *d 1.063,3.406 1.219,3.604 0.156,0.198 10 false B 0.854,3.688 1.094,3.885 0.24,0.198 10 false UP 2.406,3.396 2.802,3.594 0.396,0.198 10 false GND 2.417,3.698 2.948,3.896 0.531,0.198 10 false DOWN

*a	Component without harness connected (Power Window Regulator Motor Assembly LH)
*b	Clockwise
*c	Counterclockwise
*d	Motor Gear

Check that the motor gear rotates smoothly as follows.

OK:

Tester Connection	Specified Condition
1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more. 2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP). 3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 second.	Motor gear rotates clockwise (UP)
1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more. 2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN). 3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 second.	Motor gear rotates counterclockwise (DOWN)

Tester Connection

Specified Condition

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 second.

Motor gear rotates clockwise (UP)

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 second.

Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.

Hide Display 69810A 2.INSPECT FRONT DOOR WINDOW REGULATOR ASSEMBLY RH

NOTICE:: ·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION201902,201906,_59,_079318,_0384706,RM100000001GHZN,201906,999999,_59,_079318,_0384706,RM100000001II57,

1.635,3.49 1.26,3.49 true 1.563,3.792 1.188,3.792 true 2.333,3.781 1.958,3.781 true 2.26,3.49 1.885,3.49 true 1.781,1.625 2.719,2.313 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 0.385,1.229 0.698,1.385 0.313,0.156 10 false *b 1.229,2.146 1.542,2.302 0.313,0.156 10 false *c 2.792,2.271 3.104,2.427 0.313,0.156 10 false *d 2.375,3.708 2.99,3.906 0.615,0.198 10 false DOWN 2.344,3.427 2.958,3.625 0.615,0.198 10 false GND 0.958,3.719 1.573,3.917 0.615,0.198 10 false UP 1.021,3.427 1.635,3.625 0.615,0.198 10 false B

*a	Component without harness connected (Power Window Regulator Motor Assembly RH)
*b	Clockwise
*c	Counterclockwise
*d	Motor Gear

Check that the motor gear rotates smoothly as follows.

OK:

Tester Connection	Specified Condition
1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more. 2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP). 3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 second.	Motor gear rotates counterclockwise (UP)
1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more. 2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN). 3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 second.	Motor gear rotates clockwise (DOWN)

Tester Connection

Specified Condition

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 second.

Motor gear rotates counterclockwise (UP)

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 seconds or more.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 second.

Motor gear rotates clockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.