RM35X0E _59 Vehicle Exterior _078503 DOOR / HATCH _0381018 SLIDE DOOR CLOSER SYSTEM U

DOOR / HATCH  SLIDE DOOR CLOSER SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Rear Left Door or Rear Right Door / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Rear Left Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Pawl Switch Status of the pawl switch ON or OFF ON: Pawl switch on
OFF: Pawl switch off 		-
Half Switch Status of the half-latch switch ON or OFF ON: Half-latch switch on
OFF: Half-latch switch off 		-
Full Switch Status of the full-latch switch ON or OFF ON: Full-latch switch on
OFF: Full-latch switch off 		-
Neutral Position Close Switch Status of the neutral position close switch ON or OFF ON: Neutral position close switch on
OFF: Neutral position close switch off 		-
Neutral Position Release Switch Status of the neutral position release switch ON or OFF ON: Neutral position release switch on
OFF: Neutral position release switch off 		-
Handle Switch1 Slide door lock remote control assembly LH (close switch) signal ON or OFF ON: Slide door inside handle or outside handle close operation performed (slide door lock remote control assembly LH [close switch] on)
OFF: Slide door inside handle or outside handle operation not performed or open operation performed (slide door lock remote control assembly LH [close switch] off) 		-
Handle Switch2 Slide door lock remote control assembly LH (open switch) signal ON or OFF ON: Slide door inside handle or outside handle open operation performed (slide door lock remote control assembly LH [open switch] on)
OFF: Slide door inside handle or outside handle operation not performed or close operation performed (slide door lock remote control assembly LH [open switch] off) 		-
#Codes Number of DTCs Min.: 0, Max.: 255 Number of DTCs will be displayed -
Body Electrical > Rear Right Door > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Pawl Switch Status of the pawl switch ON or OFF ON: Pawl switch on
OFF: Pawl switch off 		-
Half Switch Status of the half-latch switch ON or OFF ON: Half-latch switch on
OFF: Half-latch switch off 		-
Full Switch Status of the full-latch switch ON or OFF ON: Full-latch switch on
OFF: Full-latch switch off 		-
Neutral Position Close Switch Status of the neutral position close switch ON or OFF ON: Neutral position close switch on
OFF: Neutral position close switch off 		-
Neutral Position Release Switch Status of the neutral position release switch ON or OFF ON: Neutral position release switch on
OFF: Neutral position release switch off 		-
Handle Switch1 Slide door lock remote control assembly RH (close switch) signal ON or OFF ON: Slide door inside handle or outside handle close operation performed (slide door lock remote control assembly RH [close switch] on)
OFF: Slide door inside handle or outside handle operation not performed or open operation performed (slide door lock remote control assembly RH [close switch] off) 		-
Handle Switch2 Slide door lock remote control assembly RH (open switch) signal ON or OFF ON: Slide door inside handle or outside handle open operation performed (slide door lock remote control assembly RH [open switch] on)
OFF: Slide door inside handle or outside handle operation not performed or close operation performed (slide door lock remote control assembly RH [open switch] off) 		-
#Codes Number of DTCs Min.: 0, Max.: 255 Number of DTCs will be displayed -


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Rear Left Door or Rear Right Door / Active Test.


e.

According to the display on GTS perform the "Active Test".

Body Electrical > Rear Left Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PSD Open Slide door LH open ON or OFF -
Body Electrical > Rear Right Door > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PSD Open Slide door RH open ON or OFF -