METER / GAUGE / DISPLAY METER / GAUGE SYSTEM ON-VEHICLE INSPECTION
PROCEDURE
1.INSPECT (for 12.3 Inch Type Multi-information Display)
- NOTICE:
- ·
The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.
·Data List values of the skid control ECU (brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
·If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Warm up the engine.
Read the Data List according to the display on the GTS.
- Chassis > Brake/EPB > Data List
-
Tester Display Measurement Item Range Normal Condition Diagnostic Note Vehicle Speed Vehicle speed Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
- Chassis > Brake/EPB > Data List
-
Tester Display Vehicle Speed - 50003 435 36
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.0 to 25.0 |
| 40 | 42.0 to 46.0 |
| 60 | 63.0 to 67.0 |
| 80 | 84.0 to 88.0 |
| 100 | 104.0 to 109.0 |
| 120 | 125.0 to 130.0 |
| 140 | 146.0 to 151.0 |
| 160 | 167.0 to 173.0 |
| 180 | 187.0 to 194.0 |
| 200 | 208.0 to 215.0 |
| 220 | 229.0 to 236.0 |
- OK:
Speedometer reading is within the acceptable range at each vehicle speed.
2.INSPECT (for 7 Inch Type Multi-information Display)
- NOTICE:
- ·
The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake actuator assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake actuator assembly) because it is the source of the vehicle speed signal.
·Data List values of the skid control ECU (brake actuator assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
·If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Warm up the engine.
Read the Data List according to the display on the GTS.
- Chassis > Brake/EPB > Data List
-
Tester Display Measurement Item Range Normal Condition Diagnostic Note Vehicle Speed Vehicle speed Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
- Chassis > Brake/EPB > Data List
-
Tester Display Vehicle Speed - 50003 435 36
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 20.5 to 23.5 |
| 40 | 41.0 to 44.0 |
| 60 | 61.5 to 64.5 |
| 80 | 82.0 to 84.0 |
| 100 | 102.5 to 104.3 |
| 120 | 123.0 to 125.0 |
| 140 | 143.4 to 146.4 |
| 160 | 163.9 to 166.9 |
| 180 | 184.4 to 187.4 |
| 200 | 204.9 to 207.9 |
| 220 | 225.4 to 228.4 |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.0 to 25.0 |
| 40 | 42.0 to 46.0 |
| 60 | 63.0 to 67.0 |
| 80 | 84.0 to 88.0 |
| 100 | 104.0 to 109.0 |
| 120 | 125.0 to 130.0 |
| 140 | 146.0 to 151.0 |
| 160 | 167.0 to 173.0 |
| 180 | 187.0 to 194.0 |
| 200 | 208.0 to 215.0 |
| 220 | 229.0 to 236.0 |
- OK:
Speedometer reading is within the acceptable range at each vehicle speed.
3.INSPECT TACHOMETER
Warm up the engine.
Read the Data List according to the display on the GTS.
- Powertrain > Engine > Data List
-
Tester Display Measurement Item Range Normal Condition Diagnostic Note Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm for Gasoline Model·750 to 850 rpm: Idling (shift lever in P, engine warmed up and A/C off)
for HEV Model·950 to 1050 rpm: Idling (shift lever in P, engine warmed up, inspection mode [maintenance mode] and not charge control)
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
- Powertrain > Engine > Data List
-
Tester Display Engine Speed - 50003 372 211
| GTS Indication (rpm) | Acceptable Range (rpm)
Data in ( ) is for Reference |
|---|---|
| 700 | 630 to 770 |
| 1000 | (900 to 1100) |
| 2000 | (1850 to 2150) |
| 3000 | 2800 to 3200 |
| 4000 | (3800 to 4200) |
| 5000 | 4800 to 5200 |
| 6000 | (5750 to 6250) |
| 7000 | 6700 to 7300 |
- OK:
Tachometer reading is within the acceptable range at each engine speed.
4.INSPECT WARNING OR INDICATOR LIGHT (INITIAL CHECK) (for 7 Inch Type Multi-information Display)
Turn the ignition switch off.
Turn the ignition switch to ON, and check the operation of the warning and indicator lights in the following table.
- OK:
All of the lights illuminate and then turn off.
Warning or Indicator Light Brake warning light / red (malfunction) Brake warning light / amber (minor malfunction) SRS warning light PCS warning light Slip indicator light VSC OFF indicator light ABS warning light Tire pressure warning light Automatic high beam indicator light Brake hold standby indicator light Brake hold operated indicator light
- HINT:
-
The illumination of each warning light and indicator light varies.