M20F-FXS, M20G-FXS ENGINE CONTROL SFI SYSTEM REGISTRATION
CAUTION / NOTICE / HINT
PROCEDURE
1. VIN (VEHICLE IDENTIFICATION NUMBER)
- NOTICE:
-
The Vehicle Identification Number (VIN) must be written to a replacement ECM.
- HINT:
-
The VIN is a 17-digit alphanumeric vehicle identification number. The GTS is required to register the VIN.
DESCRIPTION
- HINT:
-
This registration section consists of 2 parts: Read VIN and Write VIN.
Read VIN: This procedure allows the VIN stored in the ECM to be read in order to confirm that the 2 VINs, provided with the vehicle and stored in the vehicle ECM, are the same.
Write VIN: This procedure allows the VIN to be written into the ECM. If the ECM is replaced, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.
READ VIN
Confirm the vehicle VIN.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Read.
- Powertrain > Engine > Utility
-
Tester Display VIN - 50005 372 2384
According to the display on the GTS, read the VIN stored in the ECM.
WRITE VIN
Confirm the vehicle VIN.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Write.
- Powertrain > Engine > Utility
-
Tester Display VIN - 50005 372 2384
According to the display on the GTS, write the VIN to the ECM.
2. GPF DEPOSITION VALUES
- HINT:
-
These functions store and write the volumes of accumulated ash (metal oxide) and PM (Particulate Matter) that are recorded when replacing the ECM.
GPF DEPOSITION VALUES SAVE
- HINT:
-
This function stores the volumes of accumulated ash and PM recorded by the ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / GPF Deposition Values Save.
- Powertrain > Engine > Utility
-
Tester Display GPF Deposition Values Save - 50005 372 4508
According to the display on the GTS, store the volumes of accumulated ash and PM to the GTS.
GPF DEPOSITION VALUES WRITE
- HINT:
-
This function writes the volumes of accumulated ash and PM stored in the GTS.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / GPF Deposition Values Write.
- Powertrain > Engine > Utility
-
Tester Display GPF Deposition Values Write - 50005 372 4509
According to the display on the GTS, write the volumes of accumulated ash and PM to the ECM.
3. TOTAL SHORT TRIP ESTIMATE
- HINT:
-
These functions are used for reading and writing "Total Short Trip Estimate Bank 1" when replacing the ECM.
READ TOTAL SHORT TRIP ESTIMATE
- HINT:
-
This function is used for saving the value of "Total Short Trip Estimate Bank 1" when replacing the ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Total Short Trip Estimate Registration.
- Powertrain > Engine > Utility
-
Tester Display Total Short Trip Estimate Registration - 50005 372 4917
Select "Read Total Short Trip Estimate".
According to the display on the GTS, read the Total Short Trip Estimate Bank 1 stored in the ECM.
WRITE TOTAL SHORT TRIP ESTIMATE
- HINT:
-
This function is used for writing the value of "Total Short Trip Estimate Bank 1" when replacing the ECM.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Total Short Trip Estimate Registration.
- Powertrain > Engine > Utility
-
Tester Display Total Short Trip Estimate Registration - 50005 372 4917
Select "Write Total Short Trip Estimate".
According to the display on the GTS, write the Total Short Trip Estimate Bank 1 stored in the ECM.