RM38T0EC _59 Vehicle Exterior _115107 WINDOW / GLASS _0510341 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS POWER WINDOW REGULATOR MOTOR(for Rear Door) INSPECTION

PROCEDURE

Hide Display 85720E 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Check the operation.

1.5,2.594 1.917,2.844 0.417,0.25 1.24,1.625 1.656,1.625 true 1.073,3.406 1.51,3.406 true 1.094,4.021 1.49,3.833 true 1.906,3.427 2.344,3.427 true 2.313,4.021 1.938,3.823 true 2.917,2.24 2.604,2.125 false 2.771,1.802 3.01,1.802 false 0.333,2.646 0.646,2.802 0.313,0.156 10 false *a 1.063,1.51 1.375,1.667 0.313,0.156 10 false *b 1.625,2.635 1.865,2.833 0.24,0.198 10 false N2 0.906,3.302 1.219,3.458 0.313,0.156 10 false B 0.844,3.927 1.156,4.083 0.313,0.156 10 false UP 2.406,3.333 2.792,3.5 0.385,0.167 10 false GND 2.365,3.958 2.865,4.146 0.5,0.188 10 false DOWN 2.979,2.188 3.292,2.385 0.313,0.198 10 false *c 3.052,1.698 3.365,1.896 0.313,0.198 10 false *d

*a	Component without harness connected (Power Window Regulator Motor Assembly LH)
*b	Motor Gear
*c	Clockwise
*d	Counterclockwise

Connect a positive (+) lead from the auxiliary battery to connector terminal N2-2 (B).

NOTICE:: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal N2-2 (B) to avoid damaging the pulse sensor inside the motor.

ii.

Connect a negative (-) lead from the auxiliary battery to connector terminals N2-1 (GND) and N2-7 (DOWN) or N2-10 (UP).

iii.

Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition	Specified Condition
1. Connect a positive (+) lead from the auxiliary battery to terminal N2-2 (B), connect a negative (-) lead from the auxiliary battery to terminal N2-1 (GND), and keep them connected for 3 seconds or more. 2. With terminals N2-2 (B) and N2-1 (GND) connected, connect a negative (-) lead from the auxiliary battery to terminal N2-10 (UP).	Motor gear rotates clockwise
1. Connect a positive (+) lead from the auxiliary battery to terminal N2-2 (B), connect a negative (-) lead from the auxiliary battery to terminal N2-1 (GND), and keep them connected for 3 seconds or more. 2. With terminals N2-2 (B) and N2-1 (GND) connected, connect a negative (-) lead from the auxiliary battery to terminal N2-7 (DOWN).	Motor gear rotates counterclockwise

If the result is not as specified, replace the power window regulator motor assembly LH.

CAUTION:: Initialize the power window control system after installing the rear door window regulator assembly.

Hide Display 85720E 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Check the operation.

1.531,2.594 1.948,2.844 0.417,0.25 1.698,1.583 2.406,1.583 true 1.063,3.427 1.531,3.427 true 1.927,3.438 2.396,3.438 true 1.115,4.042 1.51,3.833 true 2.333,4.031 1.958,3.823 true 0.448,1.781 0.74,1.781 false 0.625,2.271 0.896,2.052 false 0.344,2.635 0.656,2.833 0.313,0.198 10 false *a 2.427,1.469 2.781,1.833 0.354,0.365 10 false *b 1.635,2.625 1.948,2.823 0.313,0.198 10 false M2 0.917,3.333 1.125,3.5 0.208,0.167 10 false B 2.438,3.354 2.854,3.563 0.417,0.208 10 false GND 0.885,3.958 1.146,4.156 0.26,0.198 10 false UP 2.385,3.958 2.885,4.177 0.5,0.219 10 false DOWN 0.229,1.688 0.542,1.885 0.313,0.198 10 false *c 0.427,2.229 0.74,2.427 0.313,0.198 10 false *d

*a	Component without harness connected (Power Window Regulator Motor Assembly RH)
*b	Motor Gear
*c	Clockwise
*d	Counterclockwise

Connect a positive (+) lead from the auxiliary battery to connector terminal M2-2 (B).

NOTICE:: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal M2-2 (B) to avoid damaging the pulse sensor inside the motor.

ii.

Connect a negative (-) lead from the auxiliary battery to connector terminals M2-1 (GND) and M2-7 (DOWN) or M2-10 (UP).

iii.

Check that the motor gear rotates smoothly as follows:

OK:

Measurement Condition	Specified Condition
1. Connect a positive (+) lead from the auxiliary battery to terminal M2-2 (B), connect a negative (-) lead from the auxiliary battery to terminal M2-1 (GND), and keep them connected for 3 seconds or more. 2. With terminals M2-2 (B) and M2-1 (GND) connected, connect a negative (-) lead from the auxiliary battery to terminal M2-10 (UP).	Motor gear rotates counterclockwise
1. Connect a positive (+) lead from the auxiliary battery to terminal M2-2 (B), connect a negative (-) lead from the auxiliary battery to terminal M2-1 (GND), and keep them connected for 3 seconds or more. 2. With terminals M2-2 (B) and M2-1 (GND) connected, connect a negative (-) lead from the auxiliary battery to terminal M2-7 (DOWN).	Motor gear rotates clockwise

If the result is not as specified, replace the power window regulator motor assembly RH.

CAUTION:: Initialize the power window control system after installing the rear door window regulator assembly.